This is the fourth Luchs in this series… and the third plastic one.
Introduction -Armory’s plastic kits
The instructions are clear and easy to follow; the one gripe I had with them is that the parts are not numbered on the sprues: you get a sprue layout on the cover of the instructions, and you have to find the parts on the sprues based on it. It’s not that difficult to do, but it still is a hindrance during the build.
The model came in an “envelope-type” box, which opens on the top (and bottom). I personally don’t like these boxes because they aren’t very resistant but it’s a personal preference. The sprues were sealed in plastic bags alongside with the PE fret, decals and instructions. The cover image shows the tank in the middle of an engagement. The back of the box shows a set of computer generated images of the model, and the different build options.
The model is a 3-in-1 type of kit: you can build three different versions of the Luchs: early, mid, and the up-armored late versions.
Inspecting the plastic parts I found a lot of flash, and the detail was somewhat soft, and in some places missing. (Most notably one of the armored protectors for the vision slots is smooth, although it was ribbed in real life.)
The PE parts are thin enough and detailed; I liked working with them. The tank is really brought to life by the PE additions; the plastic itself only gives it a basic shape, really, and the PE gives it detail.
The decals are well printed and thin; there were no issues during application.
The build was relatively quick. The lower hull does not come as a single “tub”: you have to glue it together from four parts (bottom, sides, back). The top of the hull comes as one large part. Unfortunately it goes onto the sides rather than fitting into the opening on the top, which means there will be a seam-line around the superstructure that needs to be filling.
Before installing the tracks I’ve first finished most of the hull with all the PE details, added the roadwheels, and painted the hull and the mudguards in the base color (primer red) following the base color (RAL 7028 Dunkelgelb 1944). I added the tracks at this stage, attached the mudguards, and added the remaining details to the hull. These I painted with a brush.
I carefully painted the pattern using Tamiya olive green lightened with deck tan (for scale effect) with a brush. I was not particularly concerned about how even the patches were, since they would not be prominent after the whitewash; only small parts of the underlying camouflage would be visible. I did use a light brown filter to tone down the contrast a bit. The decals were added this point, since the whitewash was applied on the field, onto a vehicle already in service.
Once the basic painting was done, I sealed the paint with Testors Dullcote to protect it from the subsequent steps, and covered the whole model with AK Interactive Heavy Chipping Medium. This was followed by Tamiya flat white, and after about ten minutes of waiting I went on creating chips with a wet brush and a toothpick. The paint was nicked carefully at places using the toothpick, and I used the wet brush to enlarge these chips.
Once I achieved a decent amount of chipping and cleaned off the model with some running water, the contrast between the white and the underlying colors was really stark.
Sealed everything with Dullcote again, and picked up MIG Ammo’s washable white. I covered the model with it using an airbrush, and after it had some time to dry I created a transparent, uneven white layer over the whole tank using a wet brush. Moving the brush with a downward motion I blended everything together nicely; the paint left a translucent white layer on top of the model.
The weathering part is always a bit difficult, especially in 1/72; it’s really easy to overdo in this scale. One thing I’ve noticed is that the camera and the eye sees differently. It’s probably the trickiest part of the whole process to make sure the model looks good on screen as well as with the naked eye. As a general rule if by eye the model looks good, on photo the effects will appear somewhat overdone.
I used some heavily diluted winter streaking grime from AK Interactive as stains on the lower chassis. Different brown pigments mixed with white spirit and “splashed mud” from Vallejo was used to simulate the mud thrown up by the tracks onto the lower chassis and the road wheels. A silver pencil helped to create a worn, shiny metal look on the edges of the tracks, and gave a metallic sheen to the gun. (Normally I use it on all edges, but in this case the whitewash made it unnecessary.) I’ve used a guitar string -E string- for the whip and the crow’s feet antennae.
Well, pretty much this was it. The model was not very difficult to build (some experience with PE required), and the detail looks good when finished. The crow’s feet antenna looks especially good compared to most of the other offerings in this scale.
Interestingly all 1/72 Luchs kits have minor differences from each other: the location of the Jerry cans, the combination of changes, the shape of the mudguards, even the turret are all slightly differ from each other. Unfortunately I cannot really comment on the accuracy of these; there are not many photos available, and they might -or might not- be representative to all the tanks produced.