Tag Archives: PE

Armory/S-models: 1/72 152mm T49 gun tank

I promised I will post finished models as well… so here is number one. (There are others lined up, I promise.)

Well, this is the actual reason for building the Armory Walker Bulldog and the S-models Sheridan… the 152mm T49 gun tank. I always wanted to build one, but did not feel like making the investment to buy two 1/35 scale models; so when Armory came out with their Bulldog, I knew I finally had the opportunity to build one in Braille.

I did not even know this tank existed until it was introduced to World of Tanks. It provided a very interesting gameplay of speed coupled with an inaccurate 152mm derp gun, so it became one of my favorite tank. The hull is the Walker Bulldog‘s, the turret was used later on the Sheridan -so putting the two together will yield you this oddity.

The conversion was quite simple: I had to cut off the turret ring from the S-model turret, and installed rare earth magnets into the models to make the switch easier. (The other option was gluing the turret to the hull.) This way I can use the same hull for two different models.

There are not many photos available of this experimental tank, so I used Citadell’s airbrush ready olive drab -a pretty good looking olive drab color, and easy to spray. I did not want to repaint the Bulldog and the Sheridan in a WoT scheme, because then I would have two tank with the same fake camo pattern (even though I do like the look of these camos). I decided to depict a battered, older Walker Bulldog hull being used as a test-bed for the prototype. This way we would expect a more pristine turret painted sitting on a relatively run-down hull. (I am sure they will repaint the prototype once the trials are over, before presenting it to the top brass, don’t worry.)

I wanted to give a shot to the AK Interactive weathering pencils for this build -dust has always been a weak point for me. These pencils are essentially the same as the aquarell pencils you can get in art stores, but the colors are developed for the modeller.

I will do a review of it, but in general, the first impressions are, well, they are OK. The best way to apply it I found was to pre-wet the surface, and then smear the pencil onto the wet surface. To see a noticable effect, you have to add a LOT – lot more than you would expect. Because of the water, the pigments tend to gravitate towards the edges (see the commander’s cupola on the photo), forming a thin, bright line, but this can be adjusted using a darker wash later on. It allows you to make mistakes, since it is very easy to re-adjust it, or just remove it (just wash it off with water), but this also means you can’t layer the effects using the same method -unless you seal everything with varnish first, which will alter the effect. I think this will be used as a last step adjustment of the overall effect. All in all, they are fine products.

And basically, that is it. Now I just have to pray for a 1/72 Object 416 and a BT-SV…

S-models 1/72 M551 Sheridan part 1


Since I want to build a 152mm gun tank T49 I needed a Walker Bulldog and a Sheridan. The Sheridan was never an issue since S-models had one; I just did not know what to expect. After all, cheap, Chinese model, basic cover art, two models per box… it does not suggest high tech, high detail model to me.

Boy was I wrong. The model is simple, builds up in an hour or so, but the detail is crisp and fine. All in all, a neat little kit with some PE added. It is missing a few details, but since this is a short project I am not fussed about it,

I only needed one Sheridan model for the T49 (the turret is fixed with rare earth magnets, so I can switch it between the Bulldog and the Sheridan), however since I had another model, I decided to build it, too. There are two 152mm gun tubes provided, so I built this with the shorter one. (I have no idea about the difference between the two.)

Now I just need to figure out what camo I want to paint it, so on it goes to the unfinished project pile… (I am working on these half-done models I promise. Apart from the Markgraf most everything is done, just need to do the photos and whatnot.)

Armory 1/72 M41A1/A2 Walker Bulldog p2.



Part 1

And the published review. (It’s probably worth checking it out if you want to build the model; I pointed out some issues with the model, and gave some tips for the build.)

Once the model was primed, I sprayed Citadel’s olive green (from the airbrush-ready range) mixed with Gunze’s yellow. The first coats had no yellow added, the subsequent coats had more and more stirred in, and I made sure I only lightly misted these on, focusing on the top of the vehicle. So the bottom of the chassis has no yellow at all, while the top received the most.

The model was fully assembled, so the tracks received some green paint; I simply went over with a black/antracite color to correct these oversprays. I found that it is quite simple and easy to paint models with tracks and all already installed, rather than trying to install the tracks on a fully painted model. The dark primer provides a very nice “shadow” to areas where the green paint did not get to.

I added the decals (one “Deliquent” decal was lost in the process…), and this is where I realized that there was not enough room between the grab handles to add the number… Something to look out for in your build. (I am not unduly worried about the turret, since I will use a different one.)

After a brown pin wash, followed with a black pinwash on the engine deck, I covered the model with semi-matte varnish.

I used Tamiya’s weathering sticks for dust and mud – again, this is not the end manifestation of the model, so I kept weathering minimum. (I found that using a wet brush to apply the product to the model, and then using a clean, wet brush to adjust the effect works wonders.) I painted the muffler cover using several rust tones, and used a silver pencil on the edges to give a metallic shine to the model.

That’s pretty much it. I am thinking about magnetizing the turret so I can just switch it (a’la KV-220, T-150) once I finish the actual model I wanted to build using this kit.


Armory 1/72 M41A1/A2 Walker Bulldog p1.


Well, I decided to buy Armory’s new injection molded model, the Walker Bulldog. I have written a review of it on Armorama; when it comes live I will link it here.

My aim with the purchase was to do a conversion, I was not particularly interested in the Bulldog itself.


As I wrote in the review, the build was pretty nice; I found no major hurdles -apart from the tool rack which I just left off. I also did not install the gun lock since I will be using the chassis for a different vehicle with a different gun. There are some minor issues with the model, but none of them are deal breaking (and at least the gun is not assembled from two halves…)


There’s an awful lot of PE coming with the kit; the smaller parts were glued on using white glue. The sink marks on the tracks are somewhat annoying but they will be filled with some mud at the end.


Next up: painting and weathering.


And then – when I buy the necessary supplies: THE CONVERSION.

Armory 1/72 VK 72.01 (K) “Fail Lowe”


When I was told I had a chance to review a model that has not even been issued yet, obviously I said yes; after all it is a rare opportunity to get your grubby hands on something so fresh out of the moulds. An added point of interest is that Armory is mostly known as a producer of high quality resin and PE aftermarket company, and their foray into the plastic scale model world is quite an interesting -and daring- step (with other resin manufacturers following suit lately).

The subject of this kit is a fictional vehicle from the popular online game World of Tanks; it it a German superheavy gift tank given out at Clan Wars, and in general it is regarded as a less-than-effective tank in-game. (Well, it might be an understatement. It’s called the Fail Lowe…) It is possible that it was an actual plan during the war, but it does not really make a difference if we call it a paper panzer or a ‘46 German tank, really. Amusing Hobby issued it in 1/35 scale; now we have a more manageable sized 1/72 version.

Armory seems to be interested in fictional German tanks for their injection moulded kits; this is the second of such vehicles, and share several parts.

The hull has a complex shape, and the surface seems rough in several places; I needed to sand the round part on the back, for example. There are no attachment points of the interlocking armor plates simulated where these plates are normally located, which is a shame (where the frontal armor meets the side armor, for example.)

The PE is top-notch, which is to be expect of Armory; they have a long experience with producing PE conversions  for both armor and aircraft, and full resin/PE models.



The model is not difficult to build, even without instructions (I used Armory’s Lowe’s instructions, the 3D renders, and the Tanks.gg website during the build). The hull is a conventional assembly of several flat parts; we don’t get a “bathtub” like lower hull. The fit is reasonably good.

I chose to assemble the running gear and the tracks before adding the mudguards.

The running gear’s attachment points are somewhat flimsy and weak; the wheels can detach quite easily after assembly, so be careful. (This seems to be a common issue; I had some problem with the running gear of Modelcollect’s E-100, too.) The idlers are done in an interesting fashion: the individual disks had to be glued on a shared axis. I did have to enlarge the holes on these wheels.

Since I did not have the instructions I was unsure how close the tracks needed to be mounted to the hull; it turns out I mounted them a bit closer than should have, and it meant some trimming and cutting, which is somewhat noticeable. (You won’t have this issue if you use the instructions, but I felt important to confess, since it’s the result of my circumstances and not the model’s fault.)

And this is the part where we come to the less-than-ideal part. The mud guards have small protruding sections sticking out to help with the attachment; these should fit into the corresponding holes placed on the side of the hull. The fact is that they don’t fit; the mudguards are quite thick and chunky, and the holes are not wide enough. This is a recurring issue with the model: several plastic parts are somewhat thick, which suggests a need to refine the plastic injection moulding process Armory uses (or replace the mudguards with PE parts…). Interestingly other parts, such as the tools and towing hooks are very finely moulded.

The top of the hull is a little bit wider than the bottom, which required some sanding to bring them to the same width. The top part is sitting on the top of the sides, which means there is a seam to be filled on the side.

This leads us to the next issue: the need for filling seams. The fit is not as good as to eliminate the need for filler. The seams between the mudguard and hull are quite wide and need to be filled. The triangular parts on the side under the round section also need filling (and they have a sink-mark as well). The turret also needs some trimming and filling to fit properly. The armored mantlet does have a seam on the artwork,so I decided not to touch it. Due to the nature of the moulding process, the muzzle breaks (there are three options to choose from) have also seams to fill, which is a bit more difficult due to the fine details. If you are patient, it’s worth drilling out the holes.

As I said the PE considerably improves the model; the engine deck grilles, etc. are very nice additions. I switched some tools to DML ones as I had those pre-painted; I also put on a 1/35 rolled tarp on the mudguard.

Overall, once I finished with the fitting and filling the build became quite enjoyable. The model looks unique, and once it takes shape, it’s a cool little thing to work on.


I chose a fictional painting scheme with my fictional tank, and used silly putty to mask the dunkelgelb parts. The Dunkelgelb is a mixture of Mig’s two kind of Dunkelgelb colors (mid and late war). I’m still a bit conflicted on these paints; if you use them right they do spray on nicely, but the fact that they form a cured layer makes them a bit less attractive for me. I’m used to the Tamiya paints, and I really like the fact I can just “mist” them on. I’m not sure I can do that with these paints.

The green was Tamiya dark green lightened with a lot of tan. The triangles were hand painted once the paint was dry. The model received a pin wash of dark brown to bring out the small details. (Looking over the photos I realized I forgot to paint the periscopes… this is something I’ll remedy tonight.)

As usual I applied filters (light brown, in several layers) to lessen the contrast, and added mud to the bottom of the chassis and running gear using pigments mixed with white spirit.

The decals were applied in a haphazard manner. I made up the identification numbers (birthday of my wife, if you really want to know), and put on the charging knight because I quite like the figure. I sealed everything with Testors dulcote.

Several layers of subtle streaking was added using AK’s Winter Streaking Grime. The photos bring out everything incredibly stark; they don’t look as strong by eye. It’s actually a good idea to take photos just to see the mistakes; it’s incredible how much more critical the camera is… (It also exaggerates the weathering effects, so keep that in mind. You can please the eye or you can please the camera; rarely can you do both…)

I used Tamiya’s makeup set on the whole model; it got a nice, uneven coat of dust (dark dust on the lower part, light dust on the upper part), which was followed by Mig’s washable dust on the horizontal surfaces. I did not use the product “straight”: I heavily diluted it with water, and added small patches where I thought dust would accumulate. With a clean, wet brush I could spread these patches, and remove the excess quite nicely. I did not add paint chips to the model; I thought I’d keep it relatively pristine. The edges got the usual treatment with a silver pencil to give a metallic shine to the model, and I declared the tank finished. (Prematurely, as I just realized, since I forgot to paint the periscopes, and lost the radio operator’s machine gun barrel somewhere in the weathering process… Let’s say he removed it for maintenance, and leave it at that.)


And that’s it, really. The model is OK; it’s not a high-tech Flyhawk kit, but it’s not bad, either. It’s something you are used to if you work with Eastern European Braille models, with one exception: the basic plastic is greatly improved by the brass barrel and extensive PE. I think it’s pretty impressive that a mostly resin/PE aftermarket company is moving to the injection moulded model market; it’s something OKB and other companies seem to be doing, too. Exciting time for the 1/72 market, that’s for sure.



Flyhawk Pz. Kpfw II Ausf L Luchs initial, special anniversary edition review, part 1




The Luchs was the final version of the veritable Panzerkampwagen II series, and was designed to serve as a reconnaissance light tank. It differed so much from any of the previous versions, it could be argued that it was a completely different design. In fact, I do argue it is a completely different design; it shares practically nothing with the original Pnz II. It was equipped with wide tracks, a torsion bar suspension, and large overlapping wheels which account for its good cross-country capabilities, and relatively high top speed. The tank was produced by MAN from 1943 to 1944; a total of about a hundred vehicles were made (from the original 800 planned). A version armed with a 5cm cannon was also in the plans, but this tank was never produced. (The word “initial” on the box hints that this version is in the works, too.) The chassis was developed by MAN, and the superstructure and turret was developed by Daimler-Benz, based on the VK 901 experimental vehicle. The engine was a 180 HP Maybach HL66P engine. The total weight was 13 tons, and the vehicle had a top speed of 60km/h, with the range of 260km on road, and 155km cross country. The tank had a crew of four (commander, gunner, driver and radio operator.) Being a light tank with the role of a reconnaissance vehicle, it was armed only with a 20mm Kw.K 38 cannon, and an MG34 machine gun. The vehicle was surprisingly well-armored for a light tank. The main weapon of the Luchs were the FuG12 and FuG Spr Ger F sets.
It served on both the Eastern and the Western Front in reconnaissance detachment of both the Wehrmacht and the Waffen-SS. The vehicles serving on the Eastern Front were supplied with additional frontal armor. The experience on the field was mixed; there were issues with reliability, and the concept of the light tank was already outdated by the time it arrived to the front, so after the first batch of 100 vehicles the production stopped.

As a side-note: this is one of my favourite tanks in World of Tanks; the amount of fun you can have when low-tier is just insane. If you play the game, get this gem in-game.

The box


Flyhawk seems to have abandoned the previous high-tech super-packages their previous models were shipped. The model arrived in a fairly large, rectangular box, with the sprues packaged in cellophane bags. (Interestingly there are two types of cellophane used in packaging…) Some parts became detached from their sprues during the transit, as the bags were free to move about in the large box, but nothing was damaged. This is a minor point; but I really liked the previous version of packaging. It gave the model a feel of having a very polished, very advanced product in your hands… kind of like the “Apple feel” you get when you pick up a brand new gadget they sell.

Nevertheless, this is the least important part of this review; after all, most of the packaging will end up in a landfill, so minimizing it makes sense on the environmental protection point of view, and not the least because it helps keeping the cost of the model down. The box art is a painting depicting the tank, with a map as a background.




The number of parts is relatively low, and we get a nice, comprehensive PE sheet along with the plastic. There is no metal barrel provided with the tank. (Which is a shame, because I prefer to use them, especially in the case of a fragile 2cm cannon. The plastic barrel is perfectly adequate, however.) The plastic is very flexible, and quite pleasant to the touch (and great to work with); cleanup is minimal, as there is almost no flash. (There are some large plastic chunks on the underside of the mudguars where the plastic was injected into the mold, but they can be cut off without any problems whatsoever.

I only had one issue: part N10 snapped into two when I tried to remove it from the sprue (it snapped when the touched it; it was probably either too thin, or already cracked). It is not a problem to replace it with a wire bent into shape. The detail is really nice (for example the padding on the interior of the turret hatch is shown; I opted to close it, though, as there is no interior detail provided.) The roadwheels are detailed very nicely, even on the side that faces towards the tank’s hull.

We also get the tiniest plastic parts I’ve ever seen (the lifting hooks for the turret), and you literally will need a magnifying glass to figure out what position they need to be glued on. You also have an option to make these hooks out of PE… We’re talking about a two-part assembly, which is smaller than a pinhead. (I took a look at them, broke into uncontrollable laughter, and decided that although I do like challenges, this time I’ll go with the plastic parts.) If you like workable hinges in 1/35 scale, you will have no problems whatsoever with these guys.

As usual, you also have the option to use PE parts instead of several plastic parts, like grab handles and the antenna, should you prefer to. (Again –see previous point… I’ve decided not to shave off the moulded on grab handles and lifting hooks from the hull, but I’ll definitely use the PE antenna for the radio.)



As an extra, we get a reclining resin figure of a tanker by Rabbit Club in his own little box.




The instructions are really nice; they are well laid-out, and use color to help the modeler with understanding the assembly very effectively. I have to say Flyhawk has some of the best instructions I’ve ever seen so far. (The English is sometimes a bit clunky, but since I’m not a native speaker either, I’m not going to start throwing stones in this particular glass-house… I do say this, however. I helped with the text on Flyhawk’s Aurora cruiser, so if you did not like the grammar there, that’s on me, and me only.)

We only get one option for finishing; a late-war three tone camouflage, but the painting guide does not say from what unit the vehicle is from. (This case I’ll build a historical model, though; but as soon as the version with the 5cm comes out, it’s going to bear the proud colors of, well, me. I’ll paint it as my in-game tank.)




I only received the tank a day ago, but I could not resist building it. It’s pretty much finished, apart from the tools, the antenna, and the running gear and tracks. (Those will be installed after much of the painting and weathering is done on the lower hull, and I’ll leave the antenna until the very last step is finished.)
In short, the assembly was a breeze. The instructions are logical and clear; I really appreciated the fact that they contain a drawing of the finished area if it makes it easier to understand what part goes where. (This is a constant problem in many other companies’ manuals…) Clearly, a lot of thought went into designing the instructions.

The fit is perfect -I did not realize at first that the sides and the bottom of the hull are two different parts, as they were already fitted together when the model arrived, for example. Despite of my initial misgivings, I had no problems handling the small parts, either. (Good tweezers are a must, though.) The only issue I ran in was the detachment of some delicate PE parts from the sheet; the metal was difficult to cut with razor blades without warping the part. A dedicated PE cutting tool is probably the best to handle these situations.

The first two steps detail the assembly of the main parts of the hull, which is followed by the suspension, and the running gear (along with small tidbits added to the hull). Step four details the assembly of the rear parts of the mudguards, and five-six details the assembly of the turret. The colors for the painting guide are given in Mr Color and Tamiya codes.


The running gear is made out of an overlapping wheel system, and a set of link-and-length tracks. There are individual track links for the drive wheel and the idler, while you’re supposed to carefully bend the straight part of the tracks to shape. The instructions provide a really clear (and colored) diagram of the track assembly.

The assembly of the turret is quite straightforward as well; I was worried a bit about the PE jerry-can holders, but they went together like a charm. There are no markings on the turret side where they are supposed to be attached, but that should really not be a problem.

The assembly to this stage took about two hours; as I said it’s not a very complicated kit to build. (The next steps will be priming, painting, fixing the tools in place, weathering, adding the wheels and tracks, weathering, mounting onto a base, and adding the antenna. I’ve managed to damage one of the width indicators already, so no more delicate, easy-to-break part will be added until the model is secure…)


I have to say, it’s been a pleasure to build this kit. I’m not sure how long it will take to finish it, as painting and weathering always takes longer than the building steps, but I shall publish the second part of this review as soon as I’m done. (The T-44 takes priority, though, so it’ll be a while.)