Tag Archives: EBR-10

Tiger Model 1/35 AML-90 Part 3. All is Dust

 

Part 1.

Part 2.

 

Magnus did nothing wrong, as we know. So dusting it up. I used AK Interactive’s Dust Effects as a base. The tutorial on the AK website is OK(ish) – the usual trick applies: you add the product, wait until it dries to the touch, and adjust it with a wet (using turpentine) brush.

The results are OK, but not good enough – the single tone and the texture alone does not work perfectly. However, as with all effects you need layers and different tones, so it is not exactly a surprise. I looked around my shelf, and took all the acrylic dust products I could find, and went working on the model.

Most of these products could be adjusted and re-adjusted with one prominent exception: once the Vallejo rain marks product hits the surface you have very little time to adjust the effect. (I had to mask the marks on the turret using pigments.)

I will do a short tutorial about the acrylic pencils; the trick is to swamp the surface with water, rub the pencils on, wait until the mess is dry, and then you can adjust with a wet brush, creating puddles, streaks and spots. Rinse and repeat. Or rather, do not rinse, just keep adjusting, maybe adding more pigments.

I am starting to feel quite good about dust; if I have a chance I would like to give Lifecolor’s liquid pigments a try, but these tools are perfectly sufficient to achieve good results.

I wrote a review of this model on Armorama as well… as you can see it has been published quite a long time ago, but the weekly publication schedule caused a considerable slip. (Hence the extra post this week. I want to get it out of the way… Still have ICM’s Leichttractor to do.)

Tiger Model 1/35 AML-90 Part 2. final assembly and painting

Part 1.

The model comes with a very well designed instruction booklet, and a colored page showing the camouflage patterns as a painting guide. The parts are well-moulded, the detail is crisp and fine, and I found no flash anywhere – it is a very high tech plastic model. There are valves, tiny nuts and all sorts of small details present on the model that you actually need a magnifying glass for. All-in-all, it is just a great little model, with just enough parts not to make it an enormous undertaking to build. You get 7 sprues with a total of 266 parts, one of which has transparent parts, 5 vinyl tires, 2 small PE with a total of 19 parts, aluminium and a brass turned barrel for the main gun and the coaxial machine gun, four metal springs and a small decal sheet.

There is a minimal PE but not exactly overdone; the fit is good, and when I dry fitted the hull to see how it holds up, it actually stayed together without glue. The detail both inside and out is good – when you open the hatches, there will be a lot of detail to see.

There is a great option of using either vinyl tires or plastic ones – as someone who does not like vinyl, I really, applaud the inclusion of hard plastic. There is also a metal barrel included for both the main gun and the coaxial machine gun, which is also very much welcome. The suspension has metal springs -they do not work, but they do look realistic. Everything is safely bagged, in color-coded bags for the springs to make the job of the builder simpler – the whole package is just geared for a pleasant building experience. (You can find photos of the sprues in this review: https://www.themodellingnews.com/2019/07/in-boxed-135th-panhard-aml-90-light.html?m=1)

The painting was done with silly putty: I left the Vallejo dark grey primer as black, and applied NATO green and brown in successive steps.

Tiger Model 1/35 AML-90 Part 1.

A nice summary of the roles of the EBR, AML and the AMX-13 -since I have been building models of all three lately. If you want to buy an actual one for reference, then you can do that, too. There was also someone who scratch-built the interior– something definitely to be admired, but not for me.

The model comes in a box that resembles the 1:48 Tamiya kits -and this is a huge compliment. The packaging is great- parts are well protected, and even color coded with different bags to make identification easy. The detail is really good, without the excess part numbers some kits tend to come with.

The building phase -so far- was a joy; my only headache is the usual problem: how to display the gorgeous interior? Are the doors big enough to give an unobstructed view of the car, or should I start cutting parts away?

The age-old question; we will see what happens once I have some time to think about it properly. Any suggestions in the comment section are welcome!

Hobby Boss 1/35 EBR-10 Part 3. -Muddying things up

opg4sia

The mud was created using Tamiya’s concerete textured paint as a base with lots of earth colored pigments and some static grass and sand added. The first batch was prepared using washable dust by Ammo, though – this represents the dried mud under all the subsequent layers. The next batch was created by adding different (and subsequently darkening) earth colored pigments; after application, as usual, I used a wet brush to adjust the effect, to remove some mud from some places, to move clumps around, and to subtly mix the different layers together. Once the lower hull and the wheels were dirtied up, I glued the wheels on.

The products for the mud I used were the following: Tamiya basing paste (concrete), Vallejo splashed mud, different earth colored pigments and sand with static grass.

(I know it is a lot… I accumulated them over the years, and never really gave them a proper tryout. It is the perfect opportunity I guess.)

If there is one fault of the kit is the tiny connection point between the axes and the wheels. It was really annoying to constantly re-gluing the whells, because the pin holding them was tiny and did not create a strong enough hold.

The last step was adding a couple of mud splashes using the above mixtures diluted with water, and a stiff old brush.

The top of the hull and the turret got some dust (washable dust by Ammo Mig, rainmarks by Vallejo), and pretty much it was it. While I do appreciate the Vallejo weathering products, as they are not solvent-based, they are more difficult to apply properly. The high surface tension of the water in them means they do not spread so easily, and they form tide marks very readily when applied to a dry surface directly. The best way I found to use them was to wet the surface, dilute the products somewhat, and keep feathering the edges of the patches so that the very marked tide-marks do not form. The key is to build up the effect in light layers. Using directly from the bottle will not yield good results.

The middle wheels were painted using AK’s True Metal paint to resemble the worn metallic surface. The same paint was used with dry brushing over some of the surfaces. The model got an overall flat coat (especially the canvas cover on the turret), and the edges were lined with silver pencil.

I did add a lot of petrol spill around the caps, but since the model was over-done, anyway, I really wanted to go the whole nine yards. Always wanted to do one of those over-weathered models… While they are certainly not realistic, they do look good. Mine looks like that the only reason why it does not fall apart due to the extensive rusting, or bursts into flames due to the gallons of spilled gasoline is the incredible amount of mud that holds the whole thing together…

I am not entirely satisfied with the results, but overall I quite like how it turned out.

By the way, the freaking wheels keep breaking off due to the tiny connecting pins snapping every time I handle the model. I gave up and used green stuff to fix them in place.

Hobby Boss 1/35 EBR-10 Part 2. Rust -and a proper tryout of Liquid Pigments by Lifecolor

A nice summary of the roles of the EBR, AML and the AMX-13 -since I have been building models of all three lately.

cjmzca5

Back to the model – building is done, proceeding to painting.

First stages…

I primed the model with Vallejo’s dark grey primer, and sprayed some rust brown over it – it will form the basis of chipping. I am going for the “World of Tanks look” – unrealistically worn armor that looks great and realistic in-game. (Figure that.)

I used the hairspray method for the larger chips – with AK’s Heavy Chipping fluid. I sprayed the fluid over the model, waited until it dried, and went over with PolyScale’s green (the label is too faded, I have no idea what green it is). I deliberately went for a light green, as it would become darker with further weathering. (I am experimenting here, so we are all very anxious of the results.)

After the paint dried I spent an exciting half an hour with some water and a stiff brush to remove some of the paint.

This is the result. It’s a bit rough on the edges, but the look is refined further in subsequent steps. (And do something about the canvas cover on the turret, I promise.)

Next up: Lifecolor’s liquid pigments -rust.

I have played around with this product, but this time I decided to give it a proper tryout. They were very useful to add rusty patches and discolorations to the model; although a lot of the effects were hidden by the subsequently added mud and dust…

As with most products it is difficult to judge the final look while it is wet; the good thing is that you can always adjust it later. If you add the different colors while the previous layers are still wet, they will mix readily; if you want to have a contrast, wait until everything dry before commencing with the next layer.

The best method was the usual one: apply, wait a bit, adjust/remove. The previous layers were very easy to remove if I was not careful; use a brush that is only a little bit wet, and do not wait until the layer you wish to adjust dries completely. (Or you can just seal everything with varnish if you choose to.)

On the top edge of the turret I tried to do some rust streaks – I have to say the liquid pigments worked just great. Once it was dry-ish, I could use a wet brush to feather the streaking a bit, just like with an enamel-based product. All-in-all I quite like these liquid pigments.

Next step -mud

 

Hobby Boss 1/35 EBR-10 part 1

3ryia1z

To help with the tedium of skype conferences, I did some work on a model waiting in the pile… the EBR-10. I became interested in it thanks to World of Tanks (a very common occurence), and since it is a fun little vehicle (which may be killing the game…) I decided to build one.

Since it is simple, I easily did it while listening in to these online conferences I am forced to attend.

Nothing special, really, most things just fell togheter. I am a bit irked by the rubber tires, and also the fact that the canvas cover of the oscillating turret is shorter than it should be, so there is a gap in the front (not on the photos, it was installed after), regardless, a fun little project – the building stage took me about 3 hours total…