Category Archives: Tamiya

Tamiya T-55A and the whole nine yards part 4.

q6m59sp

 

Please find the first, second  and third part here.

To be honest this approach of aftermarket bonanza is going to the way of the dinosaurs. MiniArt has just announced a T-55A with full interior.

Finally finished with most of the build. Getting closer to the end… Smaller jobs are finished. I did the back of the turret as best as I could. I zoomed into the box art photos of the Miniarm set, and tried to figure out what goes where. Somewhat unsuccessfully, since the instructions are frankly quite bad, too. (The PE parts are not numbered correctly for one. As mentioned the reference photos are bad, too…) The extra magazines for the machine gun mounted on the back had some hiccups. First of all I only had five in my set, not six. Second the PE straps that should have been going around them were short. What I did was simply cutting the straps in the middle, and attaching them to the front first. I added the handgrabs, and the wires to the smoke candles – soldering wire is incredibly useful for these tasks.

Well, I did the best I could -and had patience for; this will have to suffice.

I also attached the mounting points for the anti-HEAT sideskirts. Many tanks were not equipped with it, but since they are there, I might as well use them. I started with the middle section on the left side, as it has a special shape (due to the exhaust port), and used it as a reference point for the rest. The back unit is shorter than it should be, and the front overhangs a bit; somewhat annoying but easy to solve with a blade. (I simply fitted the cut off piece from the front to the back.) I’ll leave the side-skirts off for the time being; they will be attached once the main color is applied.

Tamiya wants you to make your own towing cables; it certainly makes more sense than MiniArt’s optimistic approach of prividing them as straight plastic parts. I normally use picture hanging wires for this role; it’s very life-like, and behaves like cable.

I snapped a couple of photos using my phone (hence the quality), and called it finished.

 

 

So this is where I am right now. The tank needs a base coat, and then painting can commence.

Keep tuned in…

Advertisements

Tamiya T-55A and the whole nine yards part 3.

Please find the first and second part here.

And the build goes on…

Interior

After some finishing touches to the interior, I closed the turret down. It really bothers me that I could not find a good reference for the AM version; I suspect there are a lot of screens and other digital equipment added to the standards layout.  Regardless now it looks like I’m making progress: the tank looks like a tank now. (With no gun barrel in this case.) One real complaint I have about the CMK set is that it provides no ammunition.

I’ve removed the external fuel tanks and reattached them with green stuff, as they did not sit level before. Now they look good. I will do the fuel lines a bit later on; I will use Legend’s photos as reference. (It feels somewhat like cheating, but there you go.)

Exterior

I’ve added the Eduart engine deck grilles; they really do make the model stand out. It is kind of a shame to cover all that nice, shiny brass with paint.

The road wheels were also installed. Over the years, and through the long way this model travelled with me, the poly caps somehow went missing; this made installing the wheels somewhat of a challenge. I overstepped the problems simply by sticking a small amount of green stuff into the cavity where the poly caps should have gone, and glued the wheels in place; once the green stuff set, the wheels were absolutely solidly fixed in place. As I mentioned in part 2 I’m using a Trumpeter individual track set; since the AM version had at least three different types of tracks mounted over the year I’m not too fussed about the exact type. (And now I can look forward to a tornado of incoming angry comments.)

Problems with the Miniarm set

Building the Miniarm conversion I found it out to my great annoyance that the photo of the set on the box (and the advertisement) may contain a resin machine gun, but the set itself does not contain it. After reading the fine print I now understand that this photo shows of several sets on one model, but I find the inclusion of them on the cover quite misleading. (Kind of like the Armory T-72 conversion’s case where the armored shield was not included with the set.)

I guess I’ll stick to the original Tamiya gun (which is not half bad, actually); there is no way in hell I’ll buy another set for this build. It’s getting a bit expensive, even without Fruil tracks. (I’m using someone’s unused Trumpeter individual tracklinks.)

As a side-note: comparing the Tamiya MG to the MiniArt and Trumpeter versions of similar AA heavy machine guns, the MiniArt gun wins when it comes to detail, but the Tamiya is much simpler to assemble. The Trumpeter offering is somewhere in between, but pretty impressive when it comes to detail. (And it’s a different heavy machine gun, to be fair. We’re talking about detail and ease of assembly here.) Different philosophies I guess; I think on the long run the MiniArt version is better as it does look better, but when you’re getting short on patience during a complex and difficult build (which is entirely self-imposed in this case), the Tamiya gun is a bliss. I’ll have to get an ammunition belt though, as Tamiya does not supply it.

There are other inaccuracies as well: some of the smoke candles are already discharged on the cover photo, but you only get the full ones; and the gun barrel is different. Apart from the thermal jacket issue (mentioned below in great detail), the stock photos for the set show the resin piece at the end of the gun barrel to have interior rifling -which mine does not have. To be fair the gun is capable firing an anti-tank missile (which, amusingly, costs about half of what the tank itself costs), and if I’m not mistaken the gun is actually smooth-bore. Two storage boxes only have two sides each; not sure what Miniarm was thinking when they designed them. They literally miss two sides; if you really look close, you can see under them. At this point I just ignored the issue; it would be relatively simple to fabricate the missing sides, but I only had a single damn to give, and damn is gone now. (You can see the missing sides on the photos below.)

Another contentious issue with the Miniarm set is that the instructions are horrible. There are two parts to this. The first is that in many cases the small, photocopied photographs show nothing of how the parts should be placed. You kind of see where they go, but nothing else. I found myself using google to see if I can find reference photos of the set itself to help me with it.

The second problem is that the instructions are incomplete. The back of the turret is quite busy, but you don’t really get an explanation how to use the set to build it up. It’s not very clear how to assemble the holding braces for the AA machine gun for example. I also have a bunch of unused resin parts which don’t seem to be doing anything; I do not know where they are supposed to be going. This does annoy me because I paid for them; I’d like to know how to use them. Even when something is in the instructions, sometimes it does not tell you where to put the finished artifact. In step 2-4 you are instructed to produce a part from multiple small PE pieces, but then it does not tell you what to do with it. I realized long time into the build that it’s actually supposed to be on the right side of the back of the turret. (Walkaround photos…) Also the PE frame of the gunner’s sight is simply missing. It’s there on the photos, but the instructions are quite confusing, and instruct you to cut p23 to size and glue it to the side; p23 looks nothing like the picture, and in any case, it’s shorter than required. It’s also bent, so you can’t really fit it to the straight surface.

The saga of the gun barrel

I started to work on the gun barrel. Interestingly the gun barrel on the cover photo looks absolutely different from what you get in the kit; I find this quite odd, to be honest. There must have been different versions of the T-55AM with and without thermal jacket, but I still find it curious that you get something different than that is advertised on the box cover. (I don’t even mention the fact that the photo had a brass/copper barrel, while you get an ugly aluminum one.)

I was quite wary of this stage of the build; the thermal jacket on the barrel is made out of very tiny resin parts. Especially the tie-downs are horrid: you have wrap each end of the PE tie-downs around a thin, 1.5mm long wire, and connect the two ends with a similarly short piece of wire.

I made a huge mistake and did not anneal the PE with heat before starting to work with it; it was quite difficult to wrap them around the barrel.

I started with a relatively long piece of plastic rod (and in retrospect, a thick one), glued across multiple tie-downs; once the PE set, I wrapped them around the plastic one by one. It’s not a simple process, and unfortunately the CA glue did pile up around the tiny details.

Looking at the reference photos, though, you can’t fail to notice that no matter how thick the wire you use, it will look out-of scale on the model. (Too bad I found these photos after doing most of the work already.)

These pieces of wire are meant to be the bolts holding the tie-downs in place; and they are quite small in real life. Just look at this reference photo from an AM gun barrel’s advertisement:

mm3514-4t

Looking at these photos I had one option: I cut the plastic off, and simply used the PE straps by themselves. To be honest the straps on the real gun blend in so much I could probably get away with not using them at all. (My preferred option, but I like pain, so I went with trying to glue the straps on.) This is something that’s not the set’s fault: it’s a technically quite challenging part of the build. (To make the straps themselves more to scale, it would be best to simply use strips cut from aluminium foil; even the PE is too thick for it.)

The PE ridges along the top of the gun barrel are oversized compared to the real thing. Hopefully it will not be very noticeable; the gun barrel has re-formed slits where these need to be inserted, which might hide most of their width.

Trying the gun in the resin mantlet I could not help but notice that the fit is far from snug – there will be considerable amount of filler needed to hide the gaps. It also means I’ll need something more sturdy than CA to fix it in place. (I used the good ole’ green stuff; it fixes the gun into place, and acts as a filler at the same time.)

Miniarm does offer PE lightguards, but to be honest they are difficult to assemble (and require extra wire to add), and look quite unconvincing. These guards were made of about 1.5cm thick metal rods; PE looks quite flat compared to them. (Not to mention it looks weird to mix wire with PE when all components should really look the same.) I just used the Tamiya plastic parts; they are surprisingly good.

All these complaints about the Miniarm conversion by no means are deal-breakers, but they do temper my enthusiasm about it. The detail is impressive, the resin and PE are well designed, and good quality, but I think it’s better just to get the damned Takom kit and be done with it.

Finishing touches

I’ve added all the other bits and bobs to the hull and the turret: the searchlights, various ammo boxes, handholds, wires, etc. Presently I’m looking at walkaround photos and the Takom instructions to figure out how to finish the back of the turret.

I should have finished the tracks before adding the top of the hull; this is the next big step now. The AM version had side-skirts protecting the tracks and the sides of the hull; before I add them I’ll need to install the tracks and paint the lower hull. (Which means I’ll have to learn how to use my Aztek airbrush first.) Once that is done, I can finish the sideskirts (a very daunting prospect since I can’t really make sense of the instructions at this time), and then I can at last paint this beast and be done with it.

Tamiya T-55A and the whole nine yards part 2.

x30xys8

Please find the first part here.

So the saga continues. This is, by far, the most complex build I’ve attempted: several aftermarket sets are used parallel so mistakes are a possibility. Well, mistakes have been already made.

I’ve finished up the interior finally; the CMK set is done. There are considerable differences between the interior of the T-55A and the T-55AM I’m building with the Miniarm set; however I will ignore these for the sake of my sanity. To be honest it’s difficult to find good quality references for the interior of the AM, and this is the point where I give up; it’s a hobby after all.

The hull interior was relatively simple to finish; as I said in the previous post, there are a lot of shortcuts in the CMK kit, but then again, you can argue that most of it will not be visible, anyway. The driver’s station is especially devoid of extra instruments and whatnot you can see on photos. These videos by Wargaming are really useful: one is Chieftain’s “normal” inside the tank one, the other is a pretty cool virtual video. There is also a really good one here.

I also finished the turret interior. The bottom of the turret comes as a resin replacement; I did not realize it in time but the turret ring of the Tamiya kit is actually narrower than the CMK turret’s ring. This means cutting; not the best thing to do with all the fragile PE around, so make sure you do it first – unless you like challenges as much as I do.

The gun, the turret turning mechanism, radio, different electrical boxes, the handle, etc. went in fine. I took some liberties and used some parts from the Verlinden T-62 interior set -periscopes and whatnot. I also did some cabling using soldering wire painted black. They were placed mostly using a creative licence – the actual tank has way more cables all over the place. Once all was in place, I used some diluted filters on the white -mostly light browns, and added streaking to the sides with very subtle rust colors. Did not want to make it look like it was standing abandoned for decades, but I did want to add visually interesting details. Real tanks are remarkably free of rust and rust streaks; it’s a balancing act.

Once the bottom of the turret was safely in place over the top of the hull, I started to attach the Tamiya parts for the exterior. I have to say it was a joy compared to the aftermarket set- finally everything is clear-cut and simple! Until you realize you need the next conversion set, and now you have to figure out what’s needed from the Tamiya kit, and what needs to be replaced and altered. I also noticed I was a bit hasty closing in the hull- I should have fitted the road wheels and the tracks first; it will be a bit more difficult with the mud guards in place. Well, that’s a headache for later.

The Miniarm instructions are not very good, and sometimes they just don’t warn you about minor things, like the need for filling in certain holes on the Tamiya hull. The problem is in the front: the added frontal covers most of the front, but you need to fill in two small holes. It would have been simpler if I realized it before I glued the fragile plastic parts 1 mm from the holes in question. Oh well.

The mantlet cover also comes from the Miniarm set, which interferes with the CMK gun breach making it impossible to put the top of the turret in its place. The simple solution was to cut off the front of the gun breach. Of course trying to fit the turret, and figuring out the problem meant that the delicate PE parts of the ammo holder on the back of the turret got damaged. Frankly at this point I’m not sure I’ll fix them; very little will be visible anyhow. Another issue for the next day will be the CMK coaxial machine gun; it just does not line up with the Tamiya turret.

I also realized I made a mistake at this point with the loader’s hatch: I used the CMK replacement instead of the Miniarm one. They are slightly different, but what’s done is done. The fuel tanks are provided by Miniarm, too, but the casting blocs are very thin; it’s not easy to saw them off. I’m also not sure why some tool boxes are replaced, and why others are kept from the Tamiya set… Oh well.

xbhpsei

So here we are now: the model now resembles an actual tank. (My wife says it looks like a sad, dopey-eyed vehicle.) Some detail painting is left in the turret interior, and then I can finally close it off.

I finally gave up, and bought Eduart’s engine deck grill set for the build; I hope it’s the last expense I have this with this model. It really annoys me Miniarm did not provide a set; after all, if you offer a conversion, you might as well throw in some improvements, too, saving costs for your customers. As I said the set is not cheap at all.

The next few steps will be the most painful ones: itsy-bitsy PE everywhere… That’s a story for the next post. I’m really looking forward to the painting phase.

 

 

Tamiya T-55A and the whole nine yards part 1.

y3lznvl

142119873137707
Since then I got the MiniArm set as well…

 

Well, this is one old project. This is what actually happens if you start collecting and postpone the building – your precious collection becomes outdated because newer models are issued… (Or, if you decide NOT to collect, your most desired models become out of production, and you won’t ever be able to get them again – you simply cannot win this.)

I started to collect the parts way back in 2007, when I was still in the US. Since then of course, there are models of different T-54 variants with full (well, almost full) interior, we can expect the T-55 as well (it does make sense), and of course, there’s a perfectly good (and cheap) T-55AM available by Takom. Overall, I was considering just selling the whole thing -except for the CMK interior- and buying the Takom kit instead. After much deliberation I decided to keep the original; mostly for sentimental reasons. (This is what is going to happen with the upcoming King Tiger build… I already have everything to finish up the build, so I might as well proceed, pretending the full interior 1/35 plastic kit never happened.) Since I’ve been building T-44s and T-54s left and right, I wanted to make this model look distinct -so I did the rational (airquotes) thing, and bought the MiniArm conversion set for the same amount of money the whole Takom T-55AM costs. :/ It still has no PE engine deck grilles, so that will be an interesting task; I am not prepared to spend more money on this build…

 

I was curious how the CMK set goes together. I have used the driver’s compartment part of the CMK kit for the T-44 I was building before; that part was quite familiar. Overall the set is quite good, but the instructions frankly are horrible when it comes to the ammo stowage. (It’s a shame no ammo was given with the set, by the way.) I also put the little box by the driver the wrong place; it should be a bit further back, but the instructions were not exactly clear on that part. I only noticed it when I got further down the line, and saw a drawing of the finished part.

Oh well.

The turret is quite busy- unfortunately CMK does not help with the cabling. The ammo boxes on the seat of the gunner are quite poor in detail; just a slab of rectangular resin. They should be individual ammo boxes for the coaxial MG sitting next to each other. (Similarly to the setup on step 69 on the T-54-1 instructions.)

The pre-heater for the engine cooler is also lacking detail- compared to MiniArt’s plastic interiors again. Normally it’s the other way around, but in this case the plastic model is actually more detailed than the resin one. If you’re prepared to spend money like crazy it might not be a bad idea to get a MiniArt T-54B and use the interior parts to “beef up” the CMK set. (It also provides the fuel lines for the external tanks, individual track links, and other details which are better than in the Tamiya kit.)

sqqhqmw

Since I wanted all this detail to be seen, I cut the side off the turret. It took me some time to decide what part, but at the end I settled for the left side; this will allow the interior show, without cutting away too many interesting things. (These tanks were cramped… similar cutaway will be much easier to do on the Tiger and Tiger II that are in the pipeline…)

 

Anyhow; Tamiya’s white, and the first layers of paint for the gun- that’s all for now. I’m moving to a new apartment, plus will be spending some time away, so the next update on this build will be in September most likely. I would like to make a dent on my collection of unbuilt kits, so there’s a Zvezda Pnz IV, a MiniArt Pnz III, and a DML Tiger I-II waiting to be built with full resin interiors. Not to mention the models I get for reviews, and the 1/72 stuff I still want to finish… (Modelcollect T-80, E-100 mobile rocket launcher, E-75 with interior, Hunor Nimrod, Airfix 1/12 Bentley and MiniArt T-60 with interior… And these are only the ones I can remember. My mother’s attic has a couple of really interesting models I also would like to build in the oncoming years- so subscribe, and keep your eyes on this page 🙂 )

 

Tamiya 1/35 T-62 with Verlinden damage set p4.

The first part of this build can be found here, the second here, and the third here.

4mn2vf7

Well, the small dio is finally done. It’s been a long, long build. It took me more than a year back in the US to find the conversion set; I was lucky to grab it cheap from someone who gave up on it. It then sat in a box for the next couple of years, then brought back to Europe, and finally ended up in the UK. The actual build time was a couple of months; quite quick, really, but I did take a lot of shortcuts. These were mostly done out of necessity (of preserving my sanity); the set is not exactly user-friendly. The fit is poor at places, the instructions are horrid, and some parts are just plain impossible to do (like the installation of the turret ring). I’m not even mentioning the warped parts, like the gun barrel. (Wait, I just did…) So to save time, my already thinning hair, and money, I just rolled with what I had (with the exception of the gun barrel).

Anyhow, when all is said and done, it built up into a very inaccurate, but quite nice tank.

I tried to show a gradient of colors from back to front: burned out engine compartment dominated by rust colors, to the greenish hues of the frontal hull.

ce0c9pe

The figure also took a LOT of time to hunt down; unfortunately it is long out of production, so my best bet was to get lucky and buy one from someone. (This is a really good reminder of buying things when they are available. However, it also is a sure way of building up a stash that would shame a hobby store, so there is a delicate balance to be achieved here.)

And one final word about the photography, before the pictures. I’m using a Nikon D3300 with either the kit lens (when the subject is relatively large), or a Tamron 90mm macro lens. The models are placed in a collapsible light box, and lit up using two LED lamps from the side. The whole contraption is in the kitchen, with fluorescent overall lightning, which explains the difficulties to actually getting the colors right on the photos- the camera, no matter how smart it is, is having trouble with the white balance. I did take some photos during the day using the same setup, and the sunlight as an overall source of illumination; the difference is visible. I will set the white balance manually next time. The other issue I dislike is that the figure looks a bit glossy; when you look at it in real life, it is much more matte.
It’s a learning curve of taking photos, and it’s also a matter of convenience. Living in London means I have absolutely no space dedicated for model building, so everything needs to be set up in the kitchen when I build/take photos. Not very convenient.

So without further ado, here’s the finished STALKER diorama:

Tamiya 1/35 T-62 with Verlinden damage set p3.

4zikfl6

The first part of this build can be found here.

Second part here.

With the major building and painting finished, it was time to put the tank into context. Well, into a scene, that is.

I buy large plastic cases to keep my models in; they are excellent for display, protection against dust and curious fingers, and also make it easy to transport the models. In some cases I use them as small dioramas.

In the second part the tank was reasonably finished, but it was still somewhat uniform, despite of the layers upon layers of paints, paintchips, oil paints, filters and pigments. Now was time to bring out the sponge…

The technique is reasonably simple: dab the sponge (or the scrotch brite) into the paint, dab most of it off on a piece of paper, and then keep dabbing it against the surface you wish to cover with paint/paintchips. (Depending on the amount you cover you can depict paint chips or flaking off paint.)

I’ve used the external fuel tanks to experiment; unfortunately the box was not long enough for these to be mounted onto the tank…

First, I’ve used the sponge technique to make the uniform brown surface into a rusting, multicolored one.

Second step: using light green I repeated the process. (This color is excellent for paint chips, too.) It’s not a problem if it’s too light at this stage; in fact, it’s actually necessary- the subsequent washes, filters will darken the color anyway.

And finally, the result: I’ve used overall brown washes, which created a grimy, used look. Some more green was dabbed onto the barrels in a much smaller area, and voila – we have an interesting, rusting surface with different shades and colors.

The tank was glued onto the base using two part epoxy (it’s quite heavy because of all the resin and metal), and then I used Tamiya’s soil Diorama Texture Paint. (I’ve got it discounted when the largest hobby store chain in the UK went bust a couple of years ago.) The color is not exactly great, but we’ll help it a bit later using the airbrush.

Using the sponge method I’ve added green patches onto the turret and the front part of the tank- I wanted to achieve a color difference between the front and the back.

The paint was toned down with some brown filters.

I’ve used the leftover tracklinks from the MiniArt T-54-1 for the tracks; a lot of them don’t have teeth, since they are the special links for the ice-cleats, and they are also narrower than should be, but to be honest I did not want to spend money on extra tracks. Nobody will notice, unless they read the text.

I’ve bought some AK Interactive products online cheap (six bottles for twenty quids) – rust, different colored streaking products, washes, and one that simulates algae streaking… so I used this tank to try them all.

I’ve used more rust pigments on the turret and the side of the hull, and used a dark brown filter to tone down the contrast a bit. Black pigment was used sparingly to depict soot (my fiancee’s insistence)  The way I use these pigments is to load a brush with Tamiya’s flat varnish, dab it into the pigments, dab most of it onto a piece of paper, and then dab it onto the surface of the model. You want to have some in the brush, but not too much; kind of like a heavy drybrush.

 

I’ve used some wine by Eduard to depict a creeper growing out of the driver’s compartment. The fallen leaves were made using the actual seed pod of a tree. Unfortunately I can’t figure out what it’s called; it looks like a fat caterpillar, and when you grind it up between your fingers, it falls apart into Marple-leaves like parts, and seeds. I mixed some white glue and water, added this plant material, and distributed onto the tank.

 

 

 

Last part is coming next week with the vegetation and the STALKER dude added

Tamiya 1/35 T-62 with Verlinden damage set p2.

The first part of this build can be found here.

The tank needed to be burned out and rusty- something that stood abandoned (and looted) for years. I took a lot of liberties with the amount of rust and weathering -this degree of decomposition would only happen after decades. It’s an interesting point in our hobby: we tend to overemphasise the damage, the chipping, the rusting on most of the AFVs we build, which makes them interesting to look at, but quite unrealistic and out-of-scale. The point is: it’s not meant to be an exact replica of the real thing, it’s only a representation of an idea.

The idea here is a tank that had a catastrophic fire in the engine compartment, so it was abandoned in the Exclusion Zone around Chernobyl. (I wanted to use the STALKER figure, so it had to be Chernobyl. I could not come up with a realistic scenario why a T-62 would catch fire there, though, so you’ll have to use your imagination.)

Anyhow: after spraying on a base-coat of different rust colors, I proceeded to coat the tank with AK Interactive heavy chipping medium, and some NATO green from Tamiya. Once it was dry to the touch I created areas where the paint was worn off to differing degrees: more on the back and on the thinner metallic parts, and less on the front, where the fire did not heat the hull up that much.

Once the chips were done I sealed everything with varnish.

I put the tank onto the base of the display case I intended to use and realized that it was too long for the external fuel tanks to be mounted… I could have turned the turret around if I had not used epoxy glue to stick it onto the hull… Oh well, more battle damage.

I’ve used ochre and dark brown filters on the whole of the vehicle, and some burned umber washes to deepen the shadows in the crevices.

I’ve glued the tank onto the base using epoxy glue, and mixed some sand with plaster to create a rudimentary terrain; this will -hopefully- be refined further. (As soon as I get some replacement tracks for the tank, of course.)

While we’re waiting for the groundwork to be finished, I went on to further enhance the rusty feel for the tank: I used three different colors of iron oxide (it comes in brown, red and yellow, and dabbed it on using a brush and some flat varnish.

e94tbk4

I’ve also tried Lifecolor’s rust wash set to see how it works; I suspect an airbrush would be a better way of handling it. (It is not easy to use. Well, it’s easy to use, what’s not easy is to get results like you see on the cover. Unfortunately there’s no real guide provided.)
They suggest glossy surface, however it tends to form droplets which is not ideal. (Surface tension is not always useful.)

I’ve checked out the storage box on a museum Shilka, and it was pretty much pure rust… so this is how the tool boxes will look once I’m done with it.

wi9isnw

Some more rust over the burned areas will also be necessary, and also soot. It’s a good question how much soot actually remains after years of being subjected to the elements, but this will not deter me from adding some. In fact I’ve long been wanting to add white soot left over from the burning rubber rims of the roadwheels. I’m fairly certain this would be washed away by the rain in a short order in real life, but I shall not pay attention to this issue.

Anyhow, this is how it is as of now. Keep tuned in; updates will be coming (soonish).