Category Archives: anti-tank

1/72 M56 Scorpion – OKB Grigorov

fy1jqcd1

I’ve written an in-box review of this model for Armorama; I think it’s time to show how it looks when finished.

The M56 Scorpion was an attempt to supply a gun platform for the US airborne forces that can be easily transported by airplanes, and can be deployed using an air-drop. This requirement pretty much made it impossible for the vehicle to be armored, so it is essentially a gigantic 90mm M54 gun on a dodgem chassis. Crew comfort (and safety) also took second place to the size requirements that came with the airborne deployment option.

The M56 was developed and manufactured by the Cadillac Motor Car Division of GM from 1953 to 1959. It was a small, fully tracked vehicle, powered by a 200 hp engine with a maximum road speed of 45 km/h. It had a crew of four: commander, driver, loader, gunner. The ergonomics of the vehicle were, let’s put it lightly, not very good. The loader had to disembark before the gun fired, and jump back holding the ammunition. The gun recoil also endangered the commander. The only part that can be considered armor on the vehicle is the gun shield, which has a large windscreen cut into for the driver negating its effectiveness somewhat; the rest of the self-propelled gun is about as armored as my Nissan Micra. (Another thing that it has in common with my Micra is that it has pneumatic tires…)

The M56 was in service in the USA, Spain, Morocco, and the Republic of Korea. It was used in Vietnam by the 173rd Airborne Brigade.

There are not many models available of this little AFV; I’ve found a very expensive resin one in 1/35th scale by Hobby Fan, and there’s an old OOP (and quite inaccurate) Revell kit; other than that there’s the 1/72nd scale OKB kit reviewed here. As usual, World of Tanks introduced me to this vehicle, where it is a premium American tank destroyer; and since I liked the way it looked (and have it in my garage) I was really anxious to get a model of it.

 

Considering the size of this vehicle the number of parts (especially the amount of PE) is quite high. The model is made up by approximately 70 resin pieces and about 70 PE parts… all this is in a model that can almost fit into a matchbox.

The resin is smooth, and of different color. The detail is crisp, and the fit is quite good generally. The PE frets are the thinnest I’ve ever seen. (It’s quite easy to crumple them, so be careful; it feels like a thick aluminium foil rather than photo-etched brass.) The tracks come as resin sections which need to be warmed up before shaped to the running gear. The detail is excellent, and there is very little flash anywhere.

 

The instructions are computer generated, and frankly, not very helpful. They show different views of the assembled model, but unfortunately do not instruct on actually how to put the model together. Before gluing make sure you understand how the parts should be fitting; I did make a couple of mistakes during assembly.

The exhausts for the engine seem to be shorter; there should be a section that is turning down at a right angle from the end of the exhaust pipes.

First mistake I made was to wait with the mud guard until I finished with the running gear.

If you decide to give this kit a go, make sure you glue the mudguard onto the hull first. The simple reason is that the PE covers the whole side with cutouts for the suspension units. These holes are way too tight to slide it over the suspension if it’s already in place. I had to widen these holes considerably in order to be able to fit the mudguards into place.

The other big issue for me was the suspension arms. They look very similar, but the front and rear suspension are not identical. I accidentally mixed up on one side, and hence the wheels are a bit wonky.

Other than that, most of the model went together OK. I had to make the headlight protectors out of thin wire (I normally use soldering wire as it’s quite soft). The tracks were somewhat thick and rigid, but with a lot of patience (and hot water) they did go on eventually. The hole on the gun shield has a plexi protector for the driver; I left it completely empty, since any transparent acetate sheet would look foggy and thick in this scale. (I would need something that’s about 0.2-0.3mm thick.)

I’m not sure that the back platform is depicted as open or closed up; probably closed up due to the 2 PE rails sticking out of them. (If it’s folded down, it should be longer; if it’s folded up, it should have some extra bits for the mechanism that keeps it straight in a folded -off state.) I also noticed a bit late that the loader’s seat was left off… my mistake.

The model went through multiple rounds of priming, as usual. These coats were applied more for checking for mistakes and seams rather than to provide a base coat for the paint, and was applied using a spray-can. The model was ready (I left the gun detached for easier painting), I added a final coat, and then applied Tamiya Olive Drab lightened with some Tan. (The first two photos of the painted model show the color to be a bit too greenish, flat and dull.)
A bit of yellow and ochre filter later the green became quite nice with some brownish hues. I could not find any decals that were small enough to fit onto the model, so it remained un-marked. I used Tamiya’s weathering kit (the makeup set) to apply dust and mud to the vehicle, a silver pen around the edges, to give it a metallic shine, and called it a day.

 

Altogether, the model was a pretty pleasant build -except for the little issues I mentioned. It is certainly quite pricey, as all OKB kits are, but, just like in the case of the Batchat, you really have no other options. Overall I’m pretty satisfied with the results; it is a well recommended model of a very rare subject.

DML 1/35 Marder III Ausf H – finishing up old projects

 

09rwv4s

Well, this is an old build as well. Or rather, the finishing of an old build.

I bought this model in Florida, back in 2007, and after doing a minimum amount of work on it, I just boxed it up. It stayed in a box for a long time along with a Tamiya T-62 -soon to be featured-, and a DML Sd.Kfz.250 -similarly soon to be featured.)

Anyhow, it came with me through my years doing my PhD, but I never got to work on it. I had no airbrush, no space, so I focused on 1/72.

 

Well, no more.

 

I finished the beast.

(Another confession… I just realized that there were not two, but three Marder III variants. I was under the impression this kit was a Marder III (Sd.Kfz. 139) -it goes to show how long ago I saw the instruction manual-, and I am still planning to build a Marder III Ausf M. Well, apparently, this is the third one of the two I wanted to build…)

 

Anyhow, since it’s a DML kit, it went together well; I experienced no problems with the build, aside the poor fit of the gun shield into its place on the upper hull. The detail is great, and the kit came with PE and metal gun barrel- things that made me love DML in the first place.

I got most of the sub-assemblies ready, painted and muddied up the sides of the hull so I could install the running gear and tracks, and proceeded with the painting of the rest of the vehicle.

 

I wanted to try the new (well, for me at least) Mig Ammo paints, so I got the Dunkelgelb and Olivegrun from them. I did not look up how to use them, so I did experience some problems with the paints. Before I dismissed them as crap, I found a good tutorial which highlighted the differences between these paints, and the acrylics I’ve been using. This was the first ever free-hand camo painting I’ve done; any mistakes were covered up by a layer of the base color.

Too late for this build, but still useful to know.

 

I’ve used brown filters in several light layers to blend the camo colors together; it also made the very pale base color a bit warmer and darker. Managed to break one of those backward pointing rods on the gun shield, so I replaced it with a styrene rod (I just noticed I forgot to paint it and the antenna before taking these photos).

Paintchips were painted using the base color and a dark brown color to stimulate light and deeper scratches; the metal parts were painted with AK Interactive’s True Metal paints. I left the painted parts to dry for a day, and then carefully polished them with a cotton swab. I painted some oil marks onto the large wheels; I’ve been looking forward to paint these ever since I saw how everyone else paints these wheels on the Hetzer and other Pnz 38 based vehicles; unfortunately the next layers of mud and dust covered these lovely marks up. Next time.

After washes and filters, I’ve added a copious amount of mud. It was mixed using pigments, plasters and static grass, and used a stiff brush to create splash marks.

 

Even thought I did not exactly feel inspired to do this build, and I rushed some parts of it, I feel the results are much better than I anticipated. This is the problem with backlogs- you want to get them over with, so you can concentrate on new projects. I really envy the people who have the self-control of only buying a model at a time; I still have three-four half-built models I need to finish. This one took its place next to the MiniArt SU-76 I’ve finished not long ago (also a historical build); but the other two Marder III variants will be done in 1/72 to fasten things up.

MiniArt 1/35 SU-122 build review p3.

I’m continuing the MiniArt SU-122 build and review- you can find the previous parts below:

Part 1

Part 2

You can find the photos of the parts and the instruction manual on armorama in my review, and you can find a comparison with the non-interior version of the same kit here.

If the gods will it, I should be ready in two more posts -and about two more weeks. (I hope.)

I had some constructive feedback which mentioned photo sizes. In further posts I’ll be experimenting the different options WordPress offers- thumbnails, galleries, etc. Please let me know if you have any suggestions -length, number of photos, quality of photos, style, anything. (I also would love to read comments on the models… after all, this is one of the reason for the blog.)

So, without further ado, onto the build:

Gun

The gun is not really difficult to build -except for the broken recoil guard, which I had to fix with glue. It was whole when the model came, but it snapped into three parts sometime during the build. I suggest you put this part aside before you touch the model, because it’ll break as you move the sprues around during the build. The hydraulic tubes elevating the gun are working (the two parts can move), however the way they are attached to the gun (glued to a PE holding bracket) makes this feature more like an option to fix the gun in any position you desire, than to make it adjustable after the gun is in place. In other words decide what position you’d like the gun in, put the it in place, and then glue the hydraulic tubes into place. Alternatively you can just forget about them, as they would not be visible, anyhow, and this would leave the gun movable. (In the non-interior version of this kit they are not included.)

A side-note: the wheel controlling the elevation of the gun is on the right side, between the gun and the wall of the fighting compartment… ergonomics was not a main concern when the vehicle was built.

I painted the gun in the “Russian” green color I’ll paint the whole vehicle with, and weathered it with oil washes, filters to make it look used and less uniform. Some wear-and-tear was simulated with painted chips (both black-brown and some metallic). The gun shield (not sure what it is- the fat protective shield around the base of the gun) is a three part assembly, with a prominent seam going along its length. Because the lifting hook is molded with one of the parts together, the filling and sanding requires a little care.


As you may notice the gun barrel is missing still- it is added once the gun is in its place. The plastic barrel has rifling on the inside; a pretty cool feature. One thing to mention: attach the gun barrel before you add the gun shield protecting it…

 

Engine and transmission

The building of the engine is pretty straightforward affair. The detail is pretty good, although no wiring/cabling guide is provided (which is a shame, really, but there is available reference material online). The transmission looks exceptionally well detailed; it is quite easy to see how the real thing worked once you assemble the model. The fit is really good; things snap together once in place. I painted the engine in a dark aluminium color, dry brushed it with brighter metallic shades, and weathered it using oil washes and Vajello’s engine grime product (I could not resist to try it). Some of the cabling was done using thin solder wire or Champagne bottle wire painted black (I used it to simulate cabling in the fighting compartment as well).

 

And the finished engine with the radiators attached.

 

Since I “dirtied up” the engine compartment, I added the transmission at this point because I wanted to display the model with the back folded down. I left the engine out so that it’s not going to be hidden once the model is done. (It’s a shame only the very top of it would be visible once the engine compartment is finished. Because I could not figure out how to create a realistic-looking cutaway of the engine compartment, I’m going to display it in front of the model like I did with my Hobby Boss T-34/85, and the MiniArt T-44.)

 

Some other parts: a really bent cover of the transmission… (Only my sample, apparently. I’m reviewing another SU-122 kit and the SU-85 by MiniArt, and they seem fine.)

2016_07_03_029

The cooling flaps on the engine deck are positionable; it’s a pity only the back ones will be visible; the rest will be covered up by plastic parts covering the engine deck.

up2yswc

Well, that’s it for now. Next steps: putting the interior together.

 

MiniArt 1/35 SU-122 build review p2.

Well, the vacation is over, and the work resumes. (I also had to start going to the office which tend to hinder the work that matters…)

One issue is that I’m working on several sub-assemblies parallel, so it’s difficult to show how one particular one was worked on from start to finish in one go. This is how a build normally goes, but it does not lend itself very well to a thematic review.

To start with: I’ve done some work on the ammo… I counted how many I’d need and only used that many -I don’t want to work extra when it comes to cleaning and painting identical pieces of ammunition. Aside from cleaning track links this is my least favourite part of building a model. Tiny details, multiple copies make a repetitive and very delicate task. MiniArt supplies extras of both, so it’s worth making sure you don’t do extra.

 

4xbjmva

 

Sorted… there are two kinds of ammunition provided: one type goes onto the floor of the back of the fighting compartment, the other goes on the rack by the commander. They are supposed to be painted differently (faint green and olive green), and the ones on the floor receive a small plastic disc on which they will stand. I’m not sure what the different colors signify. Perhaps high explosive and armor piercing rounds were painted and stored differently, but the instructions do not shed light on this topic.

8qkw1ed

Disclaimer: I have deviated from the instruction manual’s sequence of building, as I think it makes more sense to first build the overall structure of the vehicle and then fill it in with details. Should there were some minor fit issues, they’ll be easier to deal with as well.

The Tamiya white on the interior looked really artificial. To make it less uniform, and, well, less white, I used a very, very diluted filter (just burnt umber oil paint in turpentine). The effect was pretty good -the interior suddenly looked much more realistic.otbugyq

The engine compartment is looking better and better. Almost time to fill it up.

imvusaj

Adding smaller parts to the fighting compartment: instruments, ammo holders, compressed air bottles, etc. I also used different dark-rust colors, and different types of paints (acrylic, oil) to simulate wear and tear. This is one contentious issue: most real tanks are pretty clean from the inside. Paint chips, rust streaks take an awful lot of time to develop; more time than these vehicles were in service -or indeed survived in a war. So while I do make it look a bit worn and rusted, I do it with the understanding that it is not how the real vehicles looked like. (Maybe the SU-100s still in service all over the would do look like this after 70 years. But not a tank that has been in service for only a couple of years.)

I’ve used my favorite Vajello German Camo Black-Brown for paint chips. This color is great for simulating old, rusted metal. I applied the paint chips using both a very fine brush and with a sponge. Where the effect was too stark, I went over with some white using a sponge. (Key thing about using a sponge is to make sure you dab most of the paint out of it onto a piece of paper.)
I also used various rust colors (from reddish brown to yellow) to simulate the different colored rust, and made some light washes using these colors to stain the lower part of the hull’s interior (to simulate dirt smears). It’s important to keep in mind that the smears are not applied in one step: you add the wash (usually oil paint and turpentine), then using a clean, moistened brush you blend the stains, and carefully adjust the amount of paint on the surface. Oils are great because of they are translucent, and have a long drying time.

I made the bottom especially worn where the driver’s feet are resting.

zucp9xw

I think I went overboard with the dirt and rust on the front of the hull, but I rectified it since then using the base color.

k145lao

q6kmnt2hyf9ugdmvred0q

I’m not sure how I will display the engine- it’s simply too hidden in the engine compartment. I might go the same way as I did with the T-34 and T-44: display it outside of the vehicle. The transmission, however can be built in; I’ll simply open up the back as if the tank was undergoing maintenance.

I have ordered a couple of new products: Vajello’s engine grime, petrol stain and diesel stain. I’ve tried the petrol in the middle of the engine compartment, and the diesel next to it… I have to say they look pretty convincing.

528evih

Well, that’s it for now. The next post will be about the assembly of the gun and the engine. Please don’t hesitate to leave comments below; I always appreciate some constructive criticism. (Layout of the blog, the length of the posts, the size of the photos, the writing style, the amount of information, the techniques used… anything is free game. Just be gentle.)

 

 

 

Miniart’s SU-76(r)

b9imxxe

This model has been a shelf-queen for a long time. When I moved to the UK I was living in a ~very~ temporary student housing, so I became severely limited in what tools I could use; among other things I was forced to give up on my airbrush. (It took me five years before my living conditions changed so I was able to get another one.)
This, and the lack of space meant I had to switch to 1/72 scale… a decision which I did not regret ever since. I quite like this scale, and I think I’ll stay focused on it in the future. However, there are models which make me stray from this scale into the world of 1/35. This one, particularly, sold itself with the box art. I liked the re-painted flaking dunkelgelb camo, and the relaxing German crew -even though I ended up not using the figures for the build. (I don’t like figures on models to be honest.) Originally it was a much more ambitious project; I wanted to make a partial interior, since the driver had nothing to sit on.
I bought the kit in 2011 in Norwich, and started work on it immediately; I thought I’d progress as far as I can without an airbrush, and then just put it away until I can finish it.

Well, I stopped a bit earlier than that.

The kit is not bad, let me say this. It is, however, not a very good one, either. There are some peculiar issues with it. For one, the parts are only numbered on the instruction sheet; the numbers are not on the sprues. This forces you to constantly check for parts on the instructions showing the sprue layout, which is really, really annoying.
The other problem was the wheels. The swing arms do not “lock” in place, where they are supposed to be when the tank is on a level surface. It’s nice if you want to position the tank on uneven ground on a diorama, however it makes positioning them on a level surface difficult. The vehicle cannot sit too low or too high; knowing what the proper height is is not easy. I’ve ended up building a rig to position the wheels using an armorama topic dedicated to this issue.
And there were the fit issues. Some parts were oversized -these had to be sanded thinner. The sides of the fighting compartment had fit issues, too, so they are slightly bent- a necessity when I needed to make sure it is glued on properly.

Nevertheless, the detail is excellent; if you accept the shortcomings mentioned, the kit builds up into quite a nice representation of the vehicle.

So… without further ado, the build.

When I got the model out of its box after sitting there for years, the first thing I did was to cut the swing arms with the wheels off, and built a little rig to help me reattach them appropriately. (As you can see I painted parts in a very funky shade of green back in the days… the reason was simple: I used up a batch of paint that was mixed for a Braille scale model. Fear not: it was not intended as the actual color of the vehicle.)

mcmzjco

The gun was almost finished when I got the kit out of the box, so there was very little work left to finish it. I did a silly thing, and added the muzzle break before putting the gun into its sleeve. This meant I had to cut the gun in half, attach it to the sleeve, and then glue it together again. No biggie, but a beginner mistake.

g0bsa64

The lifting hooks had a good amount of flash around them; it was simpler just to use a piece of wire instead. (I did clean one or two, before giving up.)

wyrxl6e

The build was quite straightforward after I took care of the wheels. Once they were on, I painted the sides of the hull with green, and did the whole mud and dust routine. After that I added the tracks, and then proceeded with the rest of the build. (Once the mudguards are on, the tracks are near impossible to add.) This section had to be masked, of course, for the rest of the build, although a little overspray of Dunkelgelb and brown actually adds to the weathering effect.

qiz6rpn

cinshdo

 

wg8day0

mfrzrxk

I’ve left the sides green, figuring that the Germans would not bother cleaning and painting the areas under the mudguards. You’d have to take the tracks and wheels off, and scrub it clean before doing any sort of painting -and the results would not be visible, anyhow. This meant that the mud and dust was going on over Russian green color. The tracks were assembled without any problems; the individual links were excellent. I painted the rims black (to represent rubber), but did not worry particularly about neat lines; the wheels were about to receive quite a heavy layer of washes, mud and dust. (Yes, I was lazy.) The surface of the return rollers that rubs against the tracks was painted steel.

u8zvqzd

j10znv8

The finished gun, and the sides of the fighting compartment.

xvi0zsr

I’ve decided to leave the fighting compartment in the original green color. (I reasoned that the vehicle was adopted to German use in a field shop, so they did not strip everything to be repainted. They would probably be content on leaving the interior of the fighting compartment untouched.) This made the painting a bit more tedious (had to finish and mask the fighting compartment before proceeding). The fighting compartment itself was painted along with the rest of the model in green, and the dust/accumulated dirt added using pigments.

pcrqyll

The painting of the ammunition was a bit boring to be honest. First, you have to remove the mould seams, and then paint them one by one… not very entertaining if you ask me. I’ve used Citadel’s bronze and gold colors on the casings. I cut a couple of the projectiles off to create “used” casings, which went onto the floor of the fighting compartment, under the gun.

 

Attaching everything to the hull… the parts of the model are in various stages of painting.

ljhj7nt

tfiac6d

rdvbkwq

The gun installed… I’ve used the kit’s tow cable, which was a straight plastic part; you are supposed to bend it around the holding pins. Well, I decided to be bold, and try it, instead of using a metal tow cable. (You also get the ends of the cable as two extra separate pieces should you decide to go this route.) As expected, the plastic broke; hence the somewhat angular look.

2r7vcqp

z0lvvnq

5zawtjv

hbzlj21

Once the sub-assemblies were reasonably done, I’ve used Russian green as primer.

I wanted to depict flacking paint as I mentioned already. Since the vehicle was captured, I decided I would not only show the underlying original colors, but the rust/scratches that the vehicle has accumulated before its capture. Once the SU-76 was painted green, I’ve used dark, rust colors on edges, and other areas where heavy wear and tear was expected. The idea was that removing the Dunkelgelb from these areas would expose the base metal, while on other areas only green would show through.

rtgirwl

4v7fy1q

oohqzwl

e2vuwsy

byvh3i71

tbsp7fy

boof70i

As soon as the green dried, I applied hairspray, waited an hour, and added the Dunkelgelb coat. (Tamiya paint, lightened with tan to account for the scale effect.)

hinn9ah

Yes, you can see the numbers still…

do19t7y

Since Tamiya paints dry really fast, I could add the red-brown pattern right after the yellow base. It was necessary to add heavy layers at regions where the permanent marker showed through… I thought I was smart when I wrote the part numbers onto the plastic with a permanent marker, until the point where I realized that it showed through on everything… Some of these numbers only disappeared after the brown color was added in heavy layers. There you go: an important lesson. Don’t use permanent marker on exposed areas.

By the way, this was the first ever free-hand camo I’ve done with an airbrush.

6plexsx

pwb9eil

are3pvz

qypjstu

The chipping was done with a brush, and with a toothpick- depending on what effect I wanted to achieve. I added water to the surface with a brush, waited a bit, and then used a stiff brush/toothpick to carefully. It’s difficult not to overdo it, so it’s worth stopping now and then for a while, and put away the model for a day or so. With a fresh eye it’s easier to gauge the effect.

Once I was satisfied with how the model looked like, I sealed everything with an acrylic varnish, and applied the decals. I took some of the decals from the MiniArt T-44 set; after all, they looked good, and I liked the name on the gun.

As soon as the decals dried, I applied another layer of varnish, and started on filters. I used yellow and dark yellow colors. While the surface was still wet with the diluent, I used some dark pin washes (the wet surface ensures that the capillary action can work unimpeded even on a semi-matte surface). The same filters and washes were used in the fighting compartment as well.

Everything was sealed with varnish once again, and I started on the dust and mud. The dust was simple light colored pigments (chalk ground up) added mixed in water. Once it dried, I just brushed away the excess, and sealed it with pigment fixer.

9jgnjj7

pnkuvch

xcjax9f

bjobkij

242gcad

actnnea

yow7dil

dddkljy

qhhjpij

duxfnox

qqhlhfv

s5vl3ja

The rolled up canvas cover was a very underwhelming affair; it did not look like cloth at all. (I was not even sure what it was until I checked in the instructions; it was very symmetrical and smooth.) The cloth effect was added using oil paints. I painted the plastic with desert tan first, and then used burned umber directly from the tube to add the folded cloth look using a brush, and rubbing some off after letting it dry for a day. I’ve even painted the sides with oils to give an impression of it being rolled up. I have to say the canvas given for the T-44 is a much better affair.

j4ujz3h

psn2mdo

nzsoqiv

 

ycsclnk

 

All in all, it was a pretty good result considering how this model looked like when I got around to finally finish it. The model itself is not bad, but I think the new Tamiya offering probably supersedes it in quality. Nevertheless, fear not; it was not an unpleasant journey.

DML Flak 88 1/35 -act 2.

I’ve sung a lot of praises about the DML Flak 88 gun. I’ve shown my very first build of it -the model that has pushed me over to the armor models from airplanes-, and here is the second I did. I rarely repeat a build; normally I’d rather spend the time building something different. This is one of those kits that you MUST build, even if you prefer race cars or H0 Railroad stuff…
With this kit I wanted to depict the gun in a very different position than my first build. Whereas the first model was build showcasing the gun in a deployed state, with the gun shields attached, and in a German grey paint scheme, the new build was going to be an Afrika Korps gun without shield, still in transport mode (in which state the gun could still be fired I might add).

av0t3n7

 

vggihwr

 

The build was unremarkable. It’s a very complex model, but it’s still relatively easy to build.

ypnybov

rifling on the barreltvsvfvr4qzw8xz

 

The detail and the inclusion of extras simply make you feel like you’re working with the supercar version of scale models. Luxury in a box.

mfrj116

 

Functioning gun elevating mechanism…

xqq7tddbvw9sa0y9qftymk4r4r5siakqtto

hlqnguw

 

 

Paintingeuobvmmdnugn9nbqdgjyqltptjlmieyjzqcktiscnf8fnwzzw70waidl

 

Limbering up… the model is fully functioning in this respect as well -although you’d have to be careful about the delicate plastic parts.

lu5xgigf7gtujgpnqatiuawrxblugkpktkv2k2zzzp9xvmigg1epj4chw

 

Unfortunately, these are the photos I could find. As with the rest, all my US-built models are in storage, so I cannot show the finished product. (With the wheels on. If you can imagine the wheels, you’ll be set, though.)

 

Flak 88 (DML 1/35)

This was my very first step into the world of armor modelling, back when this kit came out.
It was a revolution of some sort. DML, which was already a respected model maker, suddenly burst into the market with a stunning model of the famous Flak 8.8. You had everything in the box to build the model, AND it cost as much as the only other game in town, the Tamiya offering from the 1970s. And when I say everything, I mean everything. Previously you had to buy metal barrels, PE, figures, individual track links (well this particular model does not have one, but the upcoming models did), etc; aftermarket parts which pushed the total cost of an armor model into the stratosphere. And now DML came, and started to issue newly designed kits using a (then) new technology of slide-moulding, with all these goodies already included – all these for lower prices than the overpriced (and antiquated) Tamiya kits. (I know I’m committing sacrilege here, but seriously: most Tamiya kits were/are reissues from the ’70s, and still show signs of motorization…)

So this was the first shot fired by DML, which was followed by their incredible Tiger series.

As I said, the model was a joy to assemble, even though it was by far the most complex I’ve ever built at that point. DML has found the perfect balance between detail, complexity and ease of build; the model does not feel overengineered or unnecessarily complex. Even the carriage worked the same way as it did in real life – you can actually put the gun into travel position once built. (The gun also has a recoil feature, which I do not understand the need for, but there it is.) I have built two of these kits: one with gun shields and unlimbered, and one on the carriage, without shield, ready to use. (These guns were designed to be used before unlimbering them; it took 8 minutes to do so, and sometimes it was not an option. So you just dropped the supports, and started shooting while still attached to the carriage.)

 

Well, this was the first of those boxes which were so full you could not closet them again upon opening…

 

You can’t help but admire the presentation.