Category Archives: 1/35

Amusing Hobby 1/35 Ferdinand with interior part 4.

Well, finishing up the interior… The previous installments:

Part 1.

Part 2.

Part 3.

The interior was a surprisingly short affair, compared to RFM’s or Takom’s Panthers‘ (which may or may not be a good thing, depending on your point of view… right now I am happy it did not take years).

I cut the floor of the fighting compartment to show off half of the electric motor, and the assorted parts; I also did a cut on the panel holding the gun, but still very little can be seen of the engines. I actually took one of them out to display it separately.

The superstructure was finished (a few bits and pieces are missing still) and weathered with AK’s interior wash, oils, chipping done with brush and sponge, and some AK rust pencils.

One issue with the decals: there are no stencils for the interior or the ammunition. It is important in this case since you can see the bottom of the rounds from above. I used RFM’s decals for the Panther ammo to depict the primer. It does improve the overall look of the model.

Based on the few photos available on the driver’s compartment it does not seem to be completely accurate, but it is easy to work with if you want to.

I also ran into the first fit issues…

  1. The horizontal cover of the driving comparment, D2, (where the extra tracklinks are stored) is too long. It needs to be filed down so it actually fits inside the hull. I did not remove enough so now it is bent… I think I will install the spare tracklinks after all to hide this shameful fact. (It was not clear when I glued it in place. The frontal part is straight as I had it pressed flat in its place – the back part, however, stayed bent.
  2. At step 33 the assembly of the air filters (those strange flower-like things on both sides of the gun) should not be done in the suggested order. The instructions would have you put the whole filter assembly together, and then install them in place. You should first glue the individual holding legs into place, and then add the top of the filters with the canisters installed.
  3. E18, the panel that holds the gun, and the top of the engines do not have enough clearance… The engines are a mm or so too high, and will not let the panel settle into its place.
  4. The superstructure has a very tight fit… I had to remove the gun, in order to be able to glue the top of the superstructure on -which obviously created fit issues with the gun later on. The gun was heavily modified: I cut off the pin that would keep it in place because once the superstructure is on, it cannot be inserted into the hole on the floor, and the gun shield was thinned somewhat. This allowed me to squeze the gun into place. Since I did not want it to be boring, I made it a slight off-center as if it was aiming at something.
  5. Part D5 (some sort of engine hatch) is too wide to fit between the superstructure and the engine deck. I had to sand it a bit off.
  6. Part J35 should be labelled B35…
  7. I am seriously considering using the flexible, rubber band tracks…

ICM 1/35 Rheinmetall Leichttraktor Part 2.

Part 1.

 You can build the whole thing before painting; there are no sub-assemblies to paint first. The instructions provide a guide to the Buntfarbenanstrich (colorful) painting scheme (https://panzerworld.com/german-armor-camouflage for more information), but I kept to the plain (and very likely non-historical) panzergray for sentimental reasons – this is how I was used to the vehicle when I played it in World of Tanks. I painted it using Tamiya acrylics: panzer grey lightened with buff for the whole tank with zenithal highlight and some panel highlighting, used light grey to further highlight edges and smaller details, and then used oils (burned umber, raw umber, green, white) to “deepen” the color with filters.

Some streaking was added, some dust and some mud, and I declared the model done. I did not want to go overboard with rust, chips and scratches, as I figured the vehicle as a prototype had no time to actually get “used in”. It spent a couple of exciting days in the proving ground, and then went back to the machine shop to be dismantled. (Sadly.)

It was also an interesting experience with the AK weathering pencils: they are pretty good at making dust. The fact that the effect can be adjusted any time after drying is great.

ICM 1/35 Rheinmetall Leichttraktor Part 1.

I am very enthusiastic about farming equipment, bulldozers and whatnot, so I was really excited when ICM announced they were going to issue a rare, interwar German agricultural mover; it represents a very important, albeit little known step in tractor development.

Incidentally it also has a turret and a gun (I guess the designers were really keen on preparing for all eventualities a farm worker might face), so we may even look at it as an early attempt at tank development by the German industry. I say “may”, since at that time the Germans were prohibited from armored vehicle development by the treaties closing WWI, it is merely a coincidence, I am sure. Regardless, these little vehicles were used by the German armed forces as a substitute during training and for the development of their armor doctrine. This is the main reason that although they never were intended for combat, they had an extremely useful role in the development of the German armored tactics (blitzkrieg) employed in WWII, and also in the development of early and mid war German armored fighting vehicles. It is indeed a welcome step from ICM to issue a plastic model of this important vehicle; it seems like the company is willing to take risks and develop models of unique subjects.

The model is very traditionally designed: the hull is made up by flat parts, the turret is made up by two semi-circular halves, necessitating filling seam lines, unfortunately which I personally do not like. (One of the boons of armor modelling in my opinion is that there is no need to fill in seam lines along the fuselage…) There is even some minimal turret interior provided; you get the main gun and the coaxial machine gun with some rudimentary detail. If you plan to leave the turret doors open, just paint the interior of the hull (but not the turret…) black.

The suspension and running gear is simplified; only the parts that show from under the side covering are detailed. Looking at the myriad of tiny road wheels it is a good thing I think… although it may be very interesting to have the option to open the side hatches to show off the suspension.

The gun has a hollowed-out end, which was solved without the use of slide-moulding: the tip is made up of two parts: the long barrel with half of the end is missing, and a tiny part that makes up for the missing half. This was it was possible to mould a short longitudinal channel in the end of the barrel, and closing it off with a small “half-pipe” forms it into a complete gun barrel with a hole at the end.

The model comes with rubber band type tracks – is a matter of taste if you prefer them or not. Talking for myself only, I consider this to be the weakest point of the model. (I prefer link-and-length tracks or individual track links, if possible. In this case definitely not individual links, though seeing how small the track links are.) You are supposed to glue two parts for one set of tracks, which leaves you with two possible seams showing where the tracks meet. I would suggest using a more discreet place to join them up than I did: the drive wheels and idlers… My mistake; as the tracks bend around the wheels the seams show up. They would all but disappear when joined flat.

The sides of the tracks do not really show segmentation where the track links meet – they are smooth, which is less-than-ideal.

All-in-all the model is well-made but geared for simplicity and ease of assembly. (I will not lie, a full interior version would be extremely welcome…) On top of the mud guards there may or may not have been some anti-slip surfacing on the real vehicle, which is lacking from this model (the mud guards are smooth). I could not decide how it was based on reference photos, but there are some builds online where this surface was added using PE by the modeller.

There are also no tools provided, which is, again, something that may be accurate; don’t forget, this vehicle was not progressed from the prototype phase. It really should not be hard to add a couple of shovels and picks should you want to include them. The weird, corkscrew-like exhaust is designed in a way that after gluing the two halves together there is no need to fill in seam lines; a very considerate way of designing models.

The thin handrails around the top of the hull are very well done, but a pain in the neck to use because it is really difficult to clean them properly from the sprue gates. They are very thin and snap easily. What I did was to shave off as much leftover plastic as I could, and then brushed on some liquid glue to melt the plastic a bit, smoothing out the sharp, protruding sprue gate remains. In all honesty if the model was not for review I would have just switched the plastic to wire, keeping the vertical holders. (It is also very easy to break them during the painting and weathering steps. Don’t ask me how I know this.)

Amusing Hobby 1/35 Ferdinand with interior part 3.

Building and painting as I go. I used AK’s French blue for the greyish/blueish parts, and a black thread for the V belt on the engine. (And lots of rust on the exhausts…)

Touching it up here and there: some red is added to to some fine details to make them pop; it will be a shame to cover it up. I think I will cut the crew compartment’s floor in half to show off what is underneath.

Tiger Model 1/35 AML-90 Part 3. All is Dust

 

Part 1.

Part 2.

 

Magnus did nothing wrong, as we know. So dusting it up. I used AK Interactive’s Dust Effects as a base. The tutorial on the AK website is OK(ish) – the usual trick applies: you add the product, wait until it dries to the touch, and adjust it with a wet (using turpentine) brush.

The results are OK, but not good enough – the single tone and the texture alone does not work perfectly. However, as with all effects you need layers and different tones, so it is not exactly a surprise. I looked around my shelf, and took all the acrylic dust products I could find, and went working on the model.

Most of these products could be adjusted and re-adjusted with one prominent exception: once the Vallejo rain marks product hits the surface you have very little time to adjust the effect. (I had to mask the marks on the turret using pigments.)

I will do a short tutorial about the acrylic pencils; the trick is to swamp the surface with water, rub the pencils on, wait until the mess is dry, and then you can adjust with a wet brush, creating puddles, streaks and spots. Rinse and repeat. Or rather, do not rinse, just keep adjusting, maybe adding more pigments.

I am starting to feel quite good about dust; if I have a chance I would like to give Lifecolor’s liquid pigments a try, but these tools are perfectly sufficient to achieve good results.

I wrote a review of this model on Armorama as well… as you can see it has been published quite a long time ago, but the weekly publication schedule caused a considerable slip. (Hence the extra post this week. I want to get it out of the way… Still have ICM’s Leichttractor to do.)

Amusing Hobby 1/35 Ferdinand with interior part 2.

Well, keep going with the interior of the lower hull. The assembly was a joy; most parts are simply dry fitted during painting as they fit really well, and slot into their respective places. Part one went well, part two continues this trend.

I gave a few, subsequently lightening coats of AK’s dunkelgelb to the bottom, and started with the ivory interior color (also AK, then misted over with MRP’s paint to lighten it on the top), using the bottom of the crew compartment as a mask (also some masking tape for the other areas not covered by it.

The gun needs some filler. Which is a bummer.

The suspension is an unique torsion bar system, which is reproduced by Amusing Hobby -at least now I know how it is supposed to work.

Does it work? Kind of.

It is very well designed, but the metal springs/torsion bars are not very strong. The metal springs have a slot on the hull which produces the tension; it is not very difficult to install them. (First I thought the metal wire hanging out of the suspension units are leftovers, but no; they do have a role.) Some of the units do have a “spring” to it, but most are quite flaccid. It does move, though.

Onto painting details – that is the topic of the next post.

Tiger Model 1/35 AML-90 Part 2. final assembly and painting

Part 1.

The model comes with a very well designed instruction booklet, and a colored page showing the camouflage patterns as a painting guide. The parts are well-moulded, the detail is crisp and fine, and I found no flash anywhere – it is a very high tech plastic model. There are valves, tiny nuts and all sorts of small details present on the model that you actually need a magnifying glass for. All-in-all, it is just a great little model, with just enough parts not to make it an enormous undertaking to build. You get 7 sprues with a total of 266 parts, one of which has transparent parts, 5 vinyl tires, 2 small PE with a total of 19 parts, aluminium and a brass turned barrel for the main gun and the coaxial machine gun, four metal springs and a small decal sheet.

There is a minimal PE but not exactly overdone; the fit is good, and when I dry fitted the hull to see how it holds up, it actually stayed together without glue. The detail both inside and out is good – when you open the hatches, there will be a lot of detail to see.

There is a great option of using either vinyl tires or plastic ones – as someone who does not like vinyl, I really, applaud the inclusion of hard plastic. There is also a metal barrel included for both the main gun and the coaxial machine gun, which is also very much welcome. The suspension has metal springs -they do not work, but they do look realistic. Everything is safely bagged, in color-coded bags for the springs to make the job of the builder simpler – the whole package is just geared for a pleasant building experience. (You can find photos of the sprues in this review: https://www.themodellingnews.com/2019/07/in-boxed-135th-panhard-aml-90-light.html?m=1)

The painting was done with silly putty: I left the Vallejo dark grey primer as black, and applied NATO green and brown in successive steps.

Amusing Hobby 1/35 Ferdinand with interior part 1.

 

I have seen the Tiger exhibition in Bovingdon, and there is an article on armorama worth reading.

I never really liked the way the Ferdinand looked- the JagdPanther had a much sleeker outline. However, it was a very intruiging vehicle due to Ferdinand Porche’s unique solution for powering this monster, which in itself made it a must to have a model with an interior.

There are only a few illustrations available of the interior of the tank online:

There is, however, a book available if you fancy buying one (and understand German -although the photos alone would be enough I suspect).

Until now there was only one option for interior: Jaguar’s set, which only consisted of the fighting and the driving compartments -not the interesting (for me at least) bits.

It is well-worth watching the Tank Museum’s Tank Chat of this tank destroyer -although regrettably they did not climb into it.

Here are some photos I took of this vehicle.

Anyhow. I decided to start this model out of the stash. The model, in general, looks simple and easy to build, despite of the complex interior – a great news indeed after the previous tribulations. The part number is suprisingly low for a kit like this, which, after the RFM Panther, is definitely welcome news… There are some annoying ejector pin marks, however. (See photos below.)

Things to keep in mind: painting and building are very interconnected. The instructions will not take into consideration the fact that several parts will be needed to be painted together, or just the opposite, need to be painted separately… I already made a couple of mistakes of gluing parts into place without thinking about how to paint them later on. This is a normal thing with all the complex models; it is up to the modeller to modify the sequence as they see fit.

The decals leave something to desire: there are no decals for the interior or the ammunition. I suspect I will just use Verlinden’s interior set, and the leftovers from the RFM/Takom Panthers for the ammunition -whomever can read the stencils can complain they are not correct for 88mm.

The engines do not have V-belts; they can be added with very little effort. If you want to do so, here is a good page for reference.

I really like that Amusing Hobby offered an alternative for tracks: either individual track links, or if you can’t be bothered with the tedium of assembly, a flexible rubber-band-like option. There is a jig provided for assembly but it is not that easy to make the tracks workable. The point of contact between the track links is really tiny, and it is very easy to get glue where it should not be,

Interior overall has a good fit, and it is well designed; so far I am really happy with the model. The fit is so good some parts are held in place firmly without glue. A lot of the parts on the photos are only dry-fit, not glued -except for those two cylinders behind the driving compartment, which I unfortunately glued in. They will need to be painted with a brush in situ.

Tiger Model 1/35 AML-90 Part 1.

A nice summary of the roles of the EBR, AML and the AMX-13 -since I have been building models of all three lately. If you want to buy an actual one for reference, then you can do that, too. There was also someone who scratch-built the interior– something definitely to be admired, but not for me.

The model comes in a box that resembles the 1:48 Tamiya kits -and this is a huge compliment. The packaging is great- parts are well protected, and even color coded with different bags to make identification easy. The detail is really good, without the excess part numbers some kits tend to come with.

The building phase -so far- was a joy; my only headache is the usual problem: how to display the gorgeous interior? Are the doors big enough to give an unobstructed view of the car, or should I start cutting parts away?

The age-old question; we will see what happens once I have some time to think about it properly. Any suggestions in the comment section are welcome!

Hobby Boss 1/35 EBR-10 Part 3. -Muddying things up

opg4sia

The mud was created using Tamiya’s concerete textured paint as a base with lots of earth colored pigments and some static grass and sand added. The first batch was prepared using washable dust by Ammo, though – this represents the dried mud under all the subsequent layers. The next batch was created by adding different (and subsequently darkening) earth colored pigments; after application, as usual, I used a wet brush to adjust the effect, to remove some mud from some places, to move clumps around, and to subtly mix the different layers together. Once the lower hull and the wheels were dirtied up, I glued the wheels on.

The products for the mud I used were the following: Tamiya basing paste (concrete), Vallejo splashed mud, different earth colored pigments and sand with static grass.

(I know it is a lot… I accumulated them over the years, and never really gave them a proper tryout. It is the perfect opportunity I guess.)

If there is one fault of the kit is the tiny connection point between the axes and the wheels. It was really annoying to constantly re-gluing the whells, because the pin holding them was tiny and did not create a strong enough hold.

The last step was adding a couple of mud splashes using the above mixtures diluted with water, and a stiff old brush.

The top of the hull and the turret got some dust (washable dust by Ammo Mig, rainmarks by Vallejo), and pretty much it was it. While I do appreciate the Vallejo weathering products, as they are not solvent-based, they are more difficult to apply properly. The high surface tension of the water in them means they do not spread so easily, and they form tide marks very readily when applied to a dry surface directly. The best way I found to use them was to wet the surface, dilute the products somewhat, and keep feathering the edges of the patches so that the very marked tide-marks do not form. The key is to build up the effect in light layers. Using directly from the bottle will not yield good results.

The middle wheels were painted using AK’s True Metal paint to resemble the worn metallic surface. The same paint was used with dry brushing over some of the surfaces. The model got an overall flat coat (especially the canvas cover on the turret), and the edges were lined with silver pencil.

I did add a lot of petrol spill around the caps, but since the model was over-done, anyway, I really wanted to go the whole nine yards. Always wanted to do one of those over-weathered models… While they are certainly not realistic, they do look good. Mine looks like that the only reason why it does not fall apart due to the extensive rusting, or bursts into flames due to the gallons of spilled gasoline is the incredible amount of mud that holds the whole thing together…

I am not entirely satisfied with the results, but overall I quite like how it turned out.

By the way, the freaking wheels keep breaking off due to the tiny connecting pins snapping every time I handle the model. I gave up and used green stuff to fix them in place.