The T-60 was born as the replacement of the outdated T-38 series of light tanks. It was designed to be easy and cheap to produce in large numbers, and to be simple to use. The idea was to build up a large number of light tanks armed with a 20mm autocannon which would support the infantry on the battlefield as a sort of cavalry. They were definitely not designed to fight other tanks or serious fortifications; they were supposed to scout, and fight infantry (and perhaps lightly armored vehicles) with their main armament. The production started in 1941 and went into 1942 with about 7000 tanks built; they served until the end of the war. (It was the third most produced armored vehicle in the Soviet Union after the T-34 and Su-76
The tank featured sloped armor, and a two-man crew. The driver was sitting in the hull, and a commander/loader/gunner was in the one-man turret behind the driver. There was no radio provided for the crew. The tank was powered by a GAZ-202 6-cylinder engine which had 76 hp, and allowed the tank to achieve a whopping 27mph top speed. The range was about 270 miles. The main armament was a 20mm TNSh cannon, which was later in the war was upgraded to a 37mm ZIS-19 gun. This upgrade was not pursued since the ammunition for the gun was in a short supply. A later upgrade to the 45mm ZIS-19 tank gun necessitated the complete redesign of the turret; this project was abandoned when the T-70 project was approved as the replacement of the T-60. As an additional claim of fame, this tank was used in the famous flying tank project- attaching glider wings to the vehicle to make it airborne.
The Germans captured and quite a lot of these tanks, but I could not find any information on what they thought of the vehicle. (They mostly used it as a towing tractor/ammo carrier, so this might indicate something.) Tanks captured by the Romanian armed forces were rebuilt into the TACAM T-60 tank destroyer.
The operational history of the T-60 was not very illustrious but it was crucial in the early days of Barbarossa when the Soviets needed tanks to hold back the German advancement while their industry was relocated further East. It was certainly reliable and could handle difficult terrain well; it was also available in large numbers -something that really counted when other, more superior weapon systems were not yet ready in large numbers. As a stop-gap solution it worked, but it was certainly not a good tank.
One of the reasons I like models with interiors is that you get an idea of what was it like for the crew to work and fight in these vehicles, and in this respect MiniArt’s offering is a very eye-opening one. I have to say based on what I’ve seen of the T-60 during the build of this model, it must have been a singularly unpleasant vehicle to be in. It was tight, cramped, and the engine was in the same compartment as the crew. The driver had a large, hot engine with rotating shafts, fuel and oil pipes all over right next to him, and the position of controls were also pretty un-ergonomical, placed as they were literally behind him. If the turret was facing forward his hatch was obstructed by the gun so leaving quickly was not much of an option, either… All this in a tank that had an armor that could be penetrated with a relatively stern look.
This tank must have been extremely dangerous to operate even in peacetime, but having people shooting at you as well will transform the picture from grim to hellish. All in all, I do not envy the people who had to fight in tanks -any tank, really- during the war, but these little vehicles must have been especially horrid. The Panzer II, it’s most comparable German counterpart, was positively luxurious compared to the T-60 -and it also had a radio.
The model is your typical Full Interior MiniArt kit. It has relatively few parts.
Normally MiniArt instructions are very easy to follow; this case I had some issues with them. For one, sometimes you have no idea how the finished article should look like (case to the point: the horn (?) assembly on the frontal glacis. For that particular part you will need to check the painting guide or historical photos.) The other, bigger is that the order of assembly does not always make sense. The most outstanding example would be the mudguards. First you add some of the tools and other details to the mudguards (e.g. holding brackets for the towing cable, but not the cable itself) but then you stop and move on to other parts of the model, leaving assemblies half-finished; later on you return and finish the build.
The other big problem was that sometimes the instructions show an assembly turned over, and then later steps showing it in the right orientation; this, combined with my inattention meant that I made a seriously silly mistake and put the main gun in the wrong position. I guess it’s fitting; as a left handed person now I can claim I have a left handed T-60. The mistake is mine, but the instructions don’t make it easy to avoid. (Interestingly enough my version now gives more clearance for the driver’s hatch to open… I think I might have improved on the design.)
Another mistake I made due to this issue was the installation of the PE bracket for the hand-crank shaft; fortunately this was easy to remedy when I realized the mistake.
The build is quite straightforward and -with some issues aside- easy. The suspension is a torsion bar suspension, but unlike in the case of the T-44, T-54, T-55 kits, it’s not functional. It is faster to assemble, but the problem is that the swing arms need to be manually positioned -something this kit shares with the older SU-76 kit. Not a big issue, but it’s not a welcome one.
The interior goes together easily. The engine has really nice detail (I could not find reference on the cables and wires, so I did not add them), and the transmission is really nice, too. I replaced the plastic rod representing the shaft of the hand-crank because it was too delicate, and broke when I removed it from the sprue. I installed the different pipes (fuel, air, etc) after I weathered the interior as they are all over the place, which would make access to certain places more difficult during the painting/weathering process.
I had some difficulties installing the gills into the back of the tank; you are supposed to place them parallel to each other and the back of the tank. The guiding ribs are not very pronounced and don’t hold them very well, so actually inserting the gills into the right ones can be a bit frustrating. (As soon as the glue “melts” the plastic a bit, the gills will freely move out of their ridge.)
The engine service hatch can be posed open, which is very much welcome, since it allows showing off the interior. (Why else build it, right?) The instructions show this as a “movable” option with a hinge; however I find this to be a very optimistic assessment: the hinge is very small, and the fit of the hatch is quite tight.
Well, this was part 1. Part to is coming next. (Duh.)